OpenPuck/OpenPuck/webusb_config.cpp

#include "webusb_config.h"
#include "board_config.h"
#include "config.h"
#include "bonds.h"
#include "rf_link.h"
#include "haptics.h"
#include "puck_hid.h"
#include "triton.h" // g_in raw IMU (diagnostic readout)
#include "lizard_map.h"
#include "build_info.h"
#include "fault_diag.h"
#include "fw_update.h"
#include "usb_tx.h"
#include "usb_mount.h" // modeSwitchReboot()
#include <Arduino.h>
#include <string.h>

Adafruit_USBD_WebUSB usb_web;

// Vendor-type control requests and the vendor interface's class requests both land on one global TinyUSB
// callback, which the Adafruit core defines for WebUSB. Linker wrapping (-Wl,--wrap, set in the Makefile)
// gives MODE_XBOX_OG first refusal on the XID requests without copying that router; whatever it declines, and
// every other mode, must still reach __real_ -- that answers WebUSB's 0x22, whose connected flag gates
// the panel sends.
bool xboxOgVendorControlXfer(uint8_t rhport, uint8_t stage,
			     const tusb_control_request_t *request);
extern "C" bool
__real_tud_vendor_control_xfer_cb(uint8_t rhport, uint8_t stage,
				  const tusb_control_request_t *request);
extern "C" bool
__wrap_tud_vendor_control_xfer_cb(uint8_t rhport, uint8_t stage,
				  const tusb_control_request_t *request)
{
	if (g_usbMode == MODE_XBOX_OG &&
	    xboxOgVendorControlXfer(rhport, stage, request))
		return true;
	return __real_tud_vendor_control_xfer_cb(rhport, stage, request);
}

// Panel-blob send is deferred to the usbd task: webusbPoll() (loop) just sets this, and webusbSofDrain()
// (registered with usb_tx, runs from tud_sof_cb on the usbd task) does the actual write+flush. usb_web.flush()
// goes through the same blocking osd_queue_send path as HID sends, so doing it from loop() could stall the
// loop and trip the watchdog under load -- with the panel open during heavy use that was a live risk.
static volatile bool g_blobRequest = false;
// Bond export ("clone" backup): a 0x09 panel command asks for a one-shot dump of all four bond slots so the
// browser can save them to a file and restore them onto a second puck. Like the status blob, the actual send
// is deferred to the usbd task (webusbSofDrain) so usb_web.write()/flush() never block loop().
static volatile bool g_bondExportRequest = false;
// Firmware-update ack ([0xAB][5][status][nextOff u32 LE]). Like the blob it is written from the usbd task
// (webusbSofDrain), but unlike the blob it is NEVER dropped -- the panel's transfer flow-control is strict
// ping-pong on these acks, so an unsent ack just stays pending until the FIFO has room (the panel is
// actively draining the IN pipe during an update, so that is at most a few SOFs).
static volatile bool g_fwupAckPend = false;
static volatile uint8_t g_fwupAckStatus = 0;
static volatile uint32_t g_fwupAckOff = 0;
static void fwupAckPost(uint8_t status)
{
	g_fwupAckStatus = status;
	g_fwupAckOff = fwupNextOff();
	g_fwupAckPend = true;
}

static bool boardCommand(uint8_t op)
{
#if !OPK_HAS_ADAFRUIT_DFU
	// The factory Open DFU bootloader uses a different settings page.
	// 0x25 (full board wipe) is rejected for the same reason AND because its recovery story doesn't exist
	// here: it erases the app expecting the resident UF2 bootloader to come up as a drag-and-drop drive,
	// and its bootloader-settings page (0xFF000) lands inside this board's factory bootloader region.
	if (op == 0x0B || op == 0x0C || op == 0x25) {
		g_blobRequest = true;
		return true;
	}
	if (op >= 0x20 && op <= 0x24) {
		fwupAckPost(FWUP_ERR_STATE);
		return true;
	}
#endif
	return false;
}

// blob payload = [ver=10][mode][mDiv][mFric][qamMap(active)][abSwap(active)][back0..3(active)][connSlot(0xFF=none)][linkUp]
//                [f1ps_lo][f1ps_hi][pollU100][newps_lo][newps_hi][e7b][relayOp][relaySub][fwdNewOnly]
//                [qos][persistMode][chordBtn B][chordBtn X][chordBtn Y][pollsps_lo][pollsps_hi]
//                [loopPeriod_lo][loopPeriod_hi][loopWorstIdx][loopWorstUs_lo][loopWorstUs_hi]
//                [pollPeriod_lo][pollPeriod_hi][logEnabled][battery%][rssi|dBm|]
//                [gitDirty][buildId 12B ASCII, NUL-padded][rsvd x3: ex rumbleScale/swProRate/swGyroScale10][raw accel ax ay az 3x s16 LE]
//                [bondedCount][slot0_up][slot0_batt][slot0_rssi]...[slot3_up][slot3_batt][slot3_rssi]
//                [v10/v17: per-type cfg, 4x9B: ET_XBOX/SWITCH/DS4/DS5 each {back0..3, qam, abSwap, padHaptics, ledBright, rumble}]
//                [v11: resetReason(RR_* code)][resetReas raw u32 LE][rxWin/10 us][hapticBlockOn][hapticBlock s]
// p[6]/p[7]/p[8..11] mirror the ACTIVE type (legacy display). v11 extends to 113 bytes (115 total incl header);
// browser reads with transferIn(128) to span the two USB-FS packets.
//                [diag: crc/s][noRx/s][rfStallRecover count]
//                [v12: relayps(lo,hi)][clkLfSrc][clkHfSrc][usPerMs(lo,hi)][hangStage][curStage][stallMs/40][ringFault(lo,hi)][hangPC u32][hangLR u32][usbdStackFree(lo,hi)][loopStackFree(lo,hi)]
//                [v13: per-slot link stats, 4x9B from p[145]: {pollsps u16, f1ps u16, newps u16, crc/s u8,
//                 noRx/s u8, relay/s u8} -- each controller's own rates (the v4 aggregates are their sums)]
//                [v14/v17: p[181] landAll87 (verbatim-0x87-relay experiment toggle)]
//                [v18: p[182..185] chordDpad left/up/right/down (back4+D-pad mode assignments)]
//                [v19: p[186] swGyroLegacy (Switch Pro gyro mapping: 0 = corrected, 1 = legacy/pre-#189)]
//                [v20: p[187..194] per-type trackpad->stick map, 4x2B {left pad, right pad} (PS_OFF/LEFT/RIGHT)]
#define WB_PAYLEN 193
// The blob send is drop-on-full (never blocks loop), so the vendor TX FIFO MUST be able to hold a whole blob
// -- otherwise tud_vendor_write_available() never reaches the frame size and EVERY frame is dropped (blank
// panel / stale mappings). The Makefile sets -DCFG_TUD_VENDOR_TX_BUFSIZE=256; guard it here so a build without
// that flag (or a future blob that outgrows the FIFO) fails loudly instead of shipping a dead panel.
static_assert(CFG_TUD_VENDOR_TX_BUFSIZE >= 2 + WB_PAYLEN,
	      "CFG_TUD_VENDOR_TX_BUFSIZE too small to hold a WebUSB blob in one "
	      "write -- build via `make build` (sets 256), or raise the flag.");
static void webusbSendBlob()
{
	if (!usb_web.connected())
		return;
	// "connected" = the most recent poll cycle's slot had a fresh F-reply (matches what the firmware
	// presents to Steam on 0x79). The blob is sent on the panel's poll, so the slot + up flag change
	// every ~250ms in normal use.
	int cs = (g_curSlot >= 0 && g_curSlot < NSLOT) ? g_curSlot : 0;
	bool up = (g_curSlot >= 0 && (millis() - g_connReplyMs[cs]) < 300);
	// STATIC, not stack: this runs on the usbd task, whose 800B stack (hardcoded USBD_STACK_SZ in the
	// Adafruit core, not growable from the sketch) is the prime overflow suspect behind the issue-72
	// watchdog hangs (hang boots report usbd stack free = 0). A 178B frame on that stack was the single
	// biggest consumer. Single-writer (SOF drain only), so a static buffer is race-free.
	static uint8_t p[2 + WB_PAYLEN];
	p[0] = 0xA5;
	p[1] = WB_PAYLEN;

	// protocol version (20 = +per-type trackpad->stick mapping (fields 80..87, blob p[187..194]);
	// 19 = +Switch Pro legacy-gyro select (field 38, blob p[186]); the rumble-strength,
	// Switch report-rate and Switch gyro-scale settings (fields 22/23/24, blob p[53..55]) are GONE -- those
	// bytes now read 0; 18 = +configurable back4+D-pad chords (fields 34..37, blob p[182..185]);
	// 17 = per-type rumble field (TypeCfg k=8), per-type stride 8->9; 16 = +configurable
	// lizard-map ops 0x11..0x15 / 0xAA frame, payload unchanged -- the panel MUST see >=16 before it dares
	// send 0x11, or a blocking readLizard() would hang forever against a firmware that silently drops the
	// unknown op; 15 = +staged firmware-update ops 0x20..0x24; 14 = +landAll87 toggle; 13 = +per-slot link
	// stats; 12 = +relay rate + clock fingerprint; 11 = +reset cause; 10 = +ledBright per type; 9 = +per-type
	// cfg; 8 = +per-slot link status; 7 = +raw accel; 6 = +swPro120/gyroScale)
	p[2] = 20;
	p[3] = g_usbMode;
	p[4] = (uint8_t)g_mDiv;
	p[5] = (uint8_t)g_mFric;
	p[6] = g_qamMap;
	p[7] = g_abSwap;
	p[8] = g_back[0];
	p[9] = g_back[1];
	p[10] = g_back[2];
	p[11] = g_back[3];
	p[12] = (g_curSlot >= 0) ? (uint8_t)g_curSlot : 0xFF;
	p[13] = up ? 1 : 0;
	p[14] = (uint8_t)g_f1ps;
	p[15] = (uint8_t)(g_f1ps >> 8);
	p[16] = (uint8_t)(g_pollUs / 100);
	p[17] = (uint8_t)g_newps;
	p[18] = (uint8_t)(g_newps >> 8);
	p[19] = g_e7b;
	p[20] = g_relayOp;
	p[21] = g_relaySub;
	p[22] = g_fwdNewOnly;
	p[23] = g_qos;
	p[24] = g_persistMode ? 1 : 0;
	p[25] = g_chordBtn[0];
	p[26] = g_chordBtn[1];
	p[27] = g_chordBtn[2];
	p[28] = (uint8_t)g_pollsps;

	// poll TX rate (vs delivered/new -> starvation vs reply-loss)
	p[29] = (uint8_t)(g_pollsps >> 8);
	p[30] = (uint8_t)g_loopPeriodUs;
	p[31] = (uint8_t)(g_loopPeriodUs >> 8); // avg loop iteration time
	p[32] = g_loopWorst;
	p[33] = (uint8_t)g_loopWorstUs;
	p[34] = (uint8_t)(g_loopWorstUs >> 8);
	p[35] = (uint8_t)g_pollPeriodUs;
	p[36] = (uint8_t)(g_pollPeriodUs >>
			  8); // measured poll period (intended 4000)
	p[37] = OPK_LOG; // logging build? panel shows/hides its log UI
	p[38] = g_battery
		[g_curSlot >= 0 && g_curSlot < NSLOT ?
			 g_curSlot :
			 0]; // controller battery % (report 0x43); 0=unknown
	p[39] = g_linkRssi[g_curSlot >= 0 && g_curSlot < NSLOT ?
				   g_curSlot :
				   0]; // RAW signal strength |dBm| (0=no sample)
	// Release builds are tagged and easier to trace by semver; local/dev builds
	// still expose git hash when no version tag is available.
	p[40] = OPK_GIT_DIRTY ? 1 : 0;
	memset(&p[41], 0, 12); // 12B ASCII build ID, NUL-padded
	{
		const char *buildId = OPK_BUILD_VERSION;
		if (buildId[0] == '\0')
			buildId = OPK_GIT_HASH;
		for (uint8_t i = 0; i < 12 && buildId[i]; i++)
			p[41 + i] = (uint8_t)buildId[i];
	}
	// v19: reserved. Were rumble strength % (v5) and the Switch Pro report rate + gyro scale (v6); all three
	// settings were removed, so these read 0 and the panel ignores them.
	p[53] = 0;
	p[54] = 0;
	p[55] = 0;
	{
		// Read the ACTIVE slot's accel, not a hardcoded g_in[0]: a controller bonded to a non-zero
		// slot leaves g_in[0] zeroed, which made this readout (and lizard) look dead.
		int16_t a[3] = { g_in[cs].ax, g_in[cs].ay, g_in[cs].az };
		memcpy(&p[56], a, 6);
	} // raw accelerometer for scale diagnostics (protocol v7)

	// per-slot link status for all bond slots (protocol v8)
	p[62] = (uint8_t)bondedSlotCount();
	{
		unsigned long nowMs = millis();
		for (int s = 0; s < NSLOT; s++) {
			bool sup = g_slot[s].used && g_connReplyMs[s] != 0 &&
				   (nowMs - g_connReplyMs[s]) < 300u;
			p[63 + s * 3] = sup ? 1 : 0;
			p[64 + s * 3] = g_battery[s];
			p[65 + s * 3] = g_linkRssi[s];
		}
	}
	// per-emulated-type button config (v10/v17): 4 types x 9 bytes from p[75]
	for (int et = 0; et < ET_COUNT; et++) {
		uint8_t *q = &p[75 + et * 9];
		q[0] = g_type[et].back[0];
		q[1] = g_type[et].back[1];
		q[2] = g_type[et].back[2];
		q[3] = g_type[et].back[3];
		q[4] = g_type[et].qamMap;
		q[5] = g_type[et].abSwap;
		q[6] = g_type[et].padHaptics;
		q[7] = g_type[et].ledBright;
		q[8] = g_type[et].rumble;
	}
	// last-boot reset cause (protocol v11): why we (re)booted -- watchdog hang vs HardFault vs intentional
	// reboot vs power-on (issue #72). p[111] = RR_* code; p[112..115] = raw RESETREAS for the curious.
	p[111] = faultDiagReason();
	uint32_t rr = faultDiagResetReas();
	p[112] = (uint8_t)rr;
	p[113] = (uint8_t)(rr >> 8);
	p[114] = (uint8_t)(rr >> 16);
	p[115] = (uint8_t)(rr >> 24);
	// Connection tunables (protocol v11): poll RX window in 10us units, post-connect haptic block enable,
	// and block duration in seconds.
	p[116] = (uint8_t)(g_rxWin / 10);
	p[117] = g_hapticBlockOn;
	p[118] = (uint8_t)(g_hapticBlockMs / 1000);
	// RF wedge diagnostics (always populated, even when the link reads down): CRC-fail/s and no-reply/s,
	// capped at 255. With Polls/s this distinguishes poll-loop-stopped vs RX-dead vs corrupt-replies.
	p[119] = (uint8_t)(g_crcps > 255 ? 255 : g_crcps);
	p[120] = (uint8_t)(g_norxps > 255 ? 255 : g_norxps);
	p[121] = (uint8_t)(g_rfStallRecover > 255 ? 255 : g_rfStallRecover);
	// v12: relay-frame TX rate (separated from true poll cycles -- Polls/s now reads ~250, Relay/s exposes the
	// host output-report flood that steals reply windows), and the clock fingerprint for clone-board triage.
	p[122] = (uint8_t)g_relayps;
	p[123] = (uint8_t)(g_relayps >> 8);
	p[124] = clockLfSrc();
	p[125] = clockHfSrc();
	uint16_t upm = clockUsPerMs();
	p[126] = (uint8_t)upm;
	p[127] = (uint8_t)(upm >> 8);
	// last hang's loop stage (0xFF = last boot wasn't a watchdog/lockup hang, or GPREGRET2 didn't survive)
	p[128] = faultDiagHangStage();
	// LIVE hang localization: current loop stage + how long loop() has been stuck (40ms units, capped). When
	// loop() wedges these keep updating because the blob is sent from the SOF interrupt, not loop().
	p[129] = faultDiagCurStage();
	uint32_t sms = faultDiagStallMs();
	p[130] = (uint8_t)(sms / 40 > 255 ? 255 : sms / 40);
	// relay-ring fault count: non-zero = we caught+recovered a desynced/corrupt ring that would otherwise be an
	// invisible IRQ-off watchdog hang. A climbing count points at the haptic relay path / memory corruption.
	p[131] = (uint8_t)g_ringFault;
	p[132] = (uint8_t)(g_ringFault >> 8);
	// PC/LR of the stuck code captured by the WDT pre-reset ISR on the last watchdog hang (0 = none captured =
	// the hang hard-masked interrupts). Map with addr2line on the .elf to name the function.
	uint32_t hpc = faultDiagHangPC(), hlr = faultDiagHangLR();
	p[133] = (uint8_t)hpc;
	p[134] = (uint8_t)(hpc >> 8);
	p[135] = (uint8_t)(hpc >> 16);
	p[136] = (uint8_t)(hpc >> 24);
	p[137] = (uint8_t)hlr;
	p[138] = (uint8_t)(hlr >> 8);
	p[139] = (uint8_t)(hlr >> 16);
	p[140] = (uint8_t)(hlr >> 24);
	// least-ever free stack (words) on the usbd task (800B total) and loop task -- usbd trending to 0 confirms
	// the overflow. words, not bytes.
	uint16_t usbdFree = faultDiagUsbdStackFree(),
		 loopFree = faultDiagLoopStackFree();
	p[141] = (uint8_t)usbdFree;
	p[142] = (uint8_t)(usbdFree >> 8);
	p[143] = (uint8_t)loopFree;
	p[144] = (uint8_t)(loopFree >> 8);
	// v13: per-slot link stats -- each controller's own poll/reply/error rates, so the panel's per-slot tabs
	// no longer conflate every controller into the aggregate numbers above.
	for (int s = 0; s < NSLOT; s++) {
		uint8_t *q = &p[145 + s * 9];
		q[0] = (uint8_t)g_slotPollsps[s];
		q[1] = (uint8_t)(g_slotPollsps[s] >> 8);
		q[2] = (uint8_t)g_slotF1ps[s];
		q[3] = (uint8_t)(g_slotF1ps[s] >> 8);
		q[4] = (uint8_t)g_slotNewps[s];
		q[5] = (uint8_t)(g_slotNewps[s] >> 8);
		q[6] = g_slotCrcps[s];
		q[7] = g_slotNoRxps[s];
		q[8] = g_slotRelayps[s];
	}
	// v14/v17: verbatim-0x87-relay experiment toggle (panel reflects + toggles it)
	p[181] = 0; // used to be g_landAll87
	// v18: back4+D-pad mode assignments (panel renders these as selects next to the B/X/Y ones)
	p[182] = g_chordDpad[CHD_LEFT];
	p[183] = g_chordDpad[CHD_UP];
	p[184] = g_chordDpad[CHD_RIGHT];
	p[185] = g_chordDpad[CHD_DOWN];
	// v19: Switch Pro gyro mapping (0 = corrected/default, 1 = legacy pre-#189 raw axes)
	p[186] = g_swGyroLegacy;
	// v20: per-type trackpad->stick mapping, {left pad, right pad} per emulated type
	for (int et = 0; et < ET_COUNT; et++) {
		p[187 + et * 2] = g_padStickCfg[et][0];
		p[188 + et * 2] = g_padStickCfg[et][1];
	}
	// CRITICAL: usb_web.write() SPINS (`while (remain && _connected) yield();`) until the IN FIFO drains or the
	// panel disconnects. If the panel holds the WebUSB interface open but stops reading its IN endpoint -- a
	// backgrounded tab, or the host briefly not servicing transferIn under load -- the FIFO never empties and
	// that spin hangs loop() until the ~8s watchdog resets us (RESETREAS=watchdog/hang). This is the ONE
	// cross-task tud_ call the marshalling refactor left able to block loop() (HID goes through the drop-oldest
	// ring; this didn't). So DROP the blob whenever the FIFO can't take it whole -- a status panel missing an
	// occasional frame is invisible, and loop() can never stall here again. (Matches the closing-the-panel
	// "fix": that just flips _connected=false to break the same spin.)
	if (tud_vendor_write_available() >= sizeof p) {
		usb_web.write(p, sizeof p);
		usb_web.flush();
	}
}

// Bond export frame (panel "Export config to file"). One self-describing frame carrying all four bond slots so
// the browser can clone a puck onto another without re-pairing:
//   [0xA7][len][ver=1][usedMask][slot0 rec 24]...[slot3 rec 24]   (len = 2 + NSLOT*24 = 98)
// usedMask bit s = slot s bonded. The session RF address is NOT exported: each puck re-derives it from the bond
// UUID + its own FICR DEVICEID at boot, and the bonded controller relearns it from the E1 host beacon on every
// reconnect (rf_link.cpp) -- so the 24-byte record is the whole portable identity. 98+2 < transferIn(128) and
// < CFG_TUD_VENDOR_TX_BUFSIZE (256), so it sends whole in one drop-on-full write like the status blob.
#define WB_BOND_PAYLEN (2 + NSLOT * 24)
static void webusbSendBondExport()
{
	if (!usb_web.connected())
		return;
	// static for the same reason as the status blob: keep the 100B frame off the 800B usbd-task stack.
	static uint8_t p[2 + WB_BOND_PAYLEN];
	p[0] = 0xA7;
	p[1] = WB_BOND_PAYLEN;
	p[2] = 1; // format version
	uint8_t mask = 0;
	for (int s = 0; s < NSLOT; s++) {
		if (g_slot[s].used)
			mask |= (uint8_t)(1u << s);
		memcpy(&p[4 + s * 24], g_slot[s].rec, 24);
	}
	p[3] = mask;
	// Same anti-hang rule as the status blob: drop the frame if the FIFO can't take it whole, never spin.
	if (tud_vendor_write_available() >= sizeof p) {
		usb_web.write(p, sizeof p);
		usb_web.flush();
	}
}

// Stream the saved (pre-reset) flight-recorder trail to the panel as 0xA8 frames. Always compiled -- the
// recorder is not OPK_LOG-gated (field hangs happen on release builds too). Frame layout mirrors the 0xA6
// capture drain so the same drop-on-full discipline applies (a write only issues when the FIFO can take the
// whole frame -> usb_web.write() never spins -> loop() never stalls here):
//   header: [0xA8][29][T=2][count u16][total u16][loopPerSec u16][stallMs][curStage][usbdStk u16][loopStk u16]
//                        [heapUsed u32][pollsps u16][relayps u16][crc u8][norx u8][heal u16][ringF u16]
//   entry:  [0xA8][9][T=1][dtMs u32][evt][stage][arg u16]     (dtMs = ms before the last recorded crumb)
//   end:    [0xA8][1][T=0]
// The panel sends 0x10 with buf[1]=1 to (re)start (emits the header + rewinds the cursor), then 0x10 buf[1]=0
// repeatedly; each call streams a budgeted chunk and the final call appends the end frame.
#define WB_FLIGHT_HDR 29
// RAII boost: these drains run from loop() and push many usb_web.write()s per call -- each enters TinyUSB's
// dcd DMA claim window (the issue-72 livelock; see usb_tx.cpp), so the whole burst runs boosted.
struct TxBoostScope {
	TxBoostScope()
	{
		usbTxBoost();
	}
	~TxBoostScope()
	{
		usbTxUnboost();
	}
};
static void webusbDrainFlight(bool restart)
{
	if (!usb_web.connected())
		return;
	TxBoostScope boost;
	if (restart) {
		faultDiagFlightDrainReset();
		if (tud_vendor_write_available() >= 2 + WB_FLIGHT_HDR) {
			struct FaultFlightVitals v;
			bool have = faultDiagFlightVitals(&v);
			if (!have)
				memset(&v, 0, sizeof v);
			uint16_t cnt = faultDiagFlightCount();
			uint16_t tot = faultDiagFlightTotal();
			uint8_t f[2 + WB_FLIGHT_HDR];
			f[0] = 0xA8;
			f[1] = WB_FLIGHT_HDR;
			f[2] = 2; // header type
			f[3] = (uint8_t)cnt;
			f[4] = (uint8_t)(cnt >> 8);
			f[5] = (uint8_t)tot;
			f[6] = (uint8_t)(tot >> 8);
			f[7] = (uint8_t)v.loopPerSec;
			f[8] = (uint8_t)(v.loopPerSec >> 8);
			f[9] = v.stallMs;
			f[10] = v.curStage;
			f[11] = (uint8_t)v.usbdStkFree;
			f[12] = (uint8_t)(v.usbdStkFree >> 8);
			f[13] = (uint8_t)v.loopStkFree;
			f[14] = (uint8_t)(v.loopStkFree >> 8);
			f[15] = (uint8_t)v.heapUsed;
			f[16] = (uint8_t)(v.heapUsed >> 8);
			f[17] = (uint8_t)(v.heapUsed >> 16);
			f[18] = (uint8_t)(v.heapUsed >> 24);
			f[19] = (uint8_t)v.pollsps;
			f[20] = (uint8_t)(v.pollsps >> 8);
			f[21] = (uint8_t)v.relayps;
			f[22] = (uint8_t)(v.relayps >> 8);
			f[23] = (uint8_t)(v.crcps > 255 ? 255 : v.crcps);
			f[24] = (uint8_t)(v.norxps > 255 ? 255 : v.norxps);
			f[25] = (uint8_t)v.rfHeal;
			f[26] = (uint8_t)(v.rfHeal >> 8);
			f[27] = (uint8_t)v.ringFault;
			f[28] = (uint8_t)(v.ringFault >> 8);
			f[29] = (uint8_t)0; // reserved / pad to header len
			f[30] = (uint8_t)0;
			usb_web.write(f, sizeof f);
			usb_web.flush();
		}
	}
	uint32_t dt = 0;
	uint8_t evt = 0, stage = 0;
	uint16_t arg = 0;
	uint16_t budget = 64;
	bool done = false;
	while (budget--) {
		if (tud_vendor_write_available() < 2 + 9)
			break; // FIFO full -> resume on the panel's next 0x10 poll
		if (!faultDiagFlightPull(&dt, &evt, &stage, &arg)) {
			done = true;
			break;
		}
		uint8_t f[2 + 9];
		f[0] = 0xA8;
		f[1] = 9;
		f[2] = 1; // entry type
		f[3] = (uint8_t)dt;
		f[4] = (uint8_t)(dt >> 8);
		f[5] = (uint8_t)(dt >> 16);
		f[6] = (uint8_t)(dt >> 24);
		f[7] = evt;
		f[8] = stage;
		f[9] = (uint8_t)arg;
		f[10] = (uint8_t)(arg >> 8);
		usb_web.write(f, sizeof f);
		usb_web.flush();
	}
	if (done && tud_vendor_write_available() >= 3) {
		uint8_t e[3] = { 0xA8, 1, 0 };
		usb_web.write(e, 3);
		usb_web.flush();
	}
}

// Runs on the usbd task (registered via usbTxRegisterDrain -> tud_sof_cb). Sends the blob if loop() asked for
// one. Keeps every usb_web write/flush off the loop task so it can't block on the device event queue.
static void webusbSofDrain(void)
{
	// If loop() has stopped beating, it's wedged -- keep pushing the blob (which carries the live stuck stage)
	// so the panel shows WHERE it hung during the ~8s before the watchdog fires. This runs on the SOF IRQ, so
	// it works even though loop() is dead. drop-on-full in webusbSendBlob keeps it from ever blocking.
	if (faultDiagStallMs() > 300)
		g_blobRequest = true;
	// firmware-update ack first: the panel is blocked on it (ping-pong), and it must never be dropped --
	// retry every SOF until the FIFO has room.
	if (g_fwupAckPend && tud_vendor_write_available() >= 7) {
		uint8_t f[7] = { 0xAB,
				 5,
				 g_fwupAckStatus,
				 (uint8_t)(g_fwupAckOff),
				 (uint8_t)(g_fwupAckOff >> 8),
				 (uint8_t)(g_fwupAckOff >> 16),
				 (uint8_t)(g_fwupAckOff >> 24) };
		usb_web.write(f, sizeof f);
		usb_web.flush();
		g_fwupAckPend = false;
	}
	if (g_blobRequest) {
		g_blobRequest = false;
		webusbSendBlob();
	}
	if (g_bondExportRequest) {
		g_bondExportRequest = false;
		webusbSendBondExport();
	}
}
// ---- live wedge reporter (0xA9) --------------------------------------------------------------------------
// THE one channel that survives a loop() wedge on boards that wipe .noinit/GPREGRET across the watchdog reset
// (Teyleten): tud_sof_cb runs on the usbd task, which is HIGHER priority than the loop() task, so the USB
// stack keeps dispatching it even while loop() is wedged (spinning or blocked) -- as long as interrupts aren't
// hard-masked (PRIMASK). When loop() has been stuck a while, emit a tiny frame carrying the stuck loop stage so
// the panel can log WHERE it hung, live, during the ~8s before the watchdog fires. Zero traffic when healthy
// (returns immediately unless stalled); rate-limited; drop-on-full so it never spins the usbd task.
//   frame: [0xA9][3][stuck stage][stallMs lo][stallMs hi]
extern "C" void tud_sof_cb(uint32_t frame_count)
{
	(void)frame_count;
	uint32_t stall = faultDiagStallMs();
	if (stall <
	    1000) // loop() healthy -> nothing to report (the common case: near-zero overhead)
		return;
	static uint32_t lastMs = 0;
	uint32_t now = millis();
	if ((uint32_t)(now - lastMs) < 200) // ~5 Hz cap
		return;
	lastMs = now;
	if (!usb_web.connected())
		return;
	uint8_t f[2 + 3];
	f[0] = 0xA9;
	f[1] = 3;
	f[2] = faultDiagCurStage();
	uint16_t s = (stall > 0xFFFFu) ? 0xFFFFu : (uint16_t)stall;
	f[3] = (uint8_t)s;
	f[4] = (uint8_t)(s >> 8);
	if (tud_vendor_write_available() >= sizeof f) {
		usb_web.write(f, sizeof f);
		usb_web.flush();
	}
}

// Register the SOF drain. Call once from setup() (harmless even if WebUSB isn't enumerated -- webusbSendBlob
// no-ops while disconnected, and g_blobRequest is only ever set by panel traffic, which needs a connection).
void webusbInit(void)
{
	usbTxRegisterDrain(webusbSofDrain);
	// Enable SOF-callback dispatch so tud_sof_cb() above fires -- our only live view into a loop() wedge on
	// boards whose bootloader wipes retained RAM. Cheap: the callback no-ops unless loop() is already stalled.
	tud_sof_cb_enable(true);
}

// Send the whole lizard binding table as one 0xAA frame so the panel can edit it:
//   [0xAA][count][ per binding (16B): outType, outData[0..6], trigMask LE(4), holdMask LE(4) ]
// Total = 2 + count*16 (max 2 + 32*16 = 514). The panel reads byte[1]=count and accumulates
// transferIn packets until it has the full frame.
static void webusbSendLizard()
{
	if (!usb_web.connected())
		return;
	uint8_t count = g_lizardMap.count;
	if (count > LZ_MAX_BINDINGS)
		count = LZ_MAX_BINDINGS;
	// static (not stack): 514 B is large for the USB task stack, and webusbPoll is single-threaded.
	static uint8_t f[2 + LZ_MAX_BINDINGS * 16];
	// 0xAA, NOT 0xA7/0xA8: main claimed 0xA7 (bond export) and 0xA8 (flight recorder), plus 0xA9 (wedge
	// reporter) and 0xAB (fwup ack) -- 0xAA is the free device->host marker for the lizard map.
	f[0] = 0xAA;
	f[1] = count;
	for (uint8_t i = 0; i < count; i++) {
		const LizardBinding &b = g_lizardMap.bindings[i];
		uint8_t *q = &f[2 + i * 16];
		q[0] = b.outType;
		for (int k = 0; k < 7; k++)
			q[1 + k] = b.outData[k];
		q[8] = (uint8_t)b.trigMask;
		q[9] = (uint8_t)(b.trigMask >> 8);
		q[10] = (uint8_t)(b.trigMask >> 16);
		q[11] = (uint8_t)(b.trigMask >> 24);
		q[12] = (uint8_t)b.holdMask;
		q[13] = (uint8_t)(b.holdMask >> 8);
		q[14] = (uint8_t)(b.holdMask >> 16);
		q[15] = (uint8_t)(b.holdMask >> 24);
	}
	usb_web.write(f, (uint16_t)(2 + count * 16));
	usb_web.flush();
}
#if OPK_LOG
// Stream the capture ring (haptics / relayed host commands) to the panel as 0xA6 frames. Frame formats:
//   entry: [0xA6][L][T=1][age u32 LE][slot][rid][n][bytes n]   (L = 8 + n)
//   end:   [0xA6][1][T=0]
static void webusbCapFrame(uint32_t ms, uint8_t slot, uint8_t rid, uint8_t nb,
			   const uint8_t *b)
{
	if (nb > 16)
		nb = 16;
	uint8_t f[2 + 9 + 16];
	uint8_t L = (uint8_t)(8 + nb);
	f[0] = 0xA6;
	f[1] = L;
	f[2] = 1;
	f[3] = (uint8_t)ms;
	f[4] = (uint8_t)(ms >> 8);
	f[5] = (uint8_t)(ms >> 16);
	f[6] = (uint8_t)(ms >> 24); // absolute log time
	f[7] = slot;
	f[8] = rid;
	f[9] = nb;
	memcpy(f + 10, b, nb);
	usb_web.write(f, (uint16_t)(2 + L));
	usb_web.flush();
}
static void webusbCapEnd()
{
	uint8_t e[3] = { 0xA6, 1, 0 };
	usb_web.write(e, 3);
	usb_web.flush();
}
// 0x06: drain entries since the last drain (or since the 0x05 start/rewind). The panel polls this on a
// timer and accumulates, so a dump-from-boot of the whole ring streams over many polls without blocking the
// loop. A per-call budget bounds how long one poll spends here.
static void webusbDrainCapture()
{
	if (!usb_web.connected())
		return;
	TxBoostScope
		boost; // capture streams at flood rate through the same dcd DMA window
	uint32_t ms = 0;
	uint8_t slot = 0, rid = 0, nb = 0, b[16];
	uint16_t budget = 128;
	// Same anti-hang rule as the blob: webusbCapFrame's usb_web.write() spins until the FIFO drains, so stop
	// pulling the moment the FIFO can't hold a max-size frame (2+9+16=27 B) -- the panel resumes the drain on
	// its next 0x06 poll. Never let a backed-up panel hang loop() here.
	while (budget-- && tud_vendor_write_available() >= 27 &&
	       hapLogPull(&ms, &slot, &rid, &nb, b))
		webusbCapFrame(ms, slot, rid, nb, b);
	if (tud_vendor_write_available() >= 3)
		webusbCapEnd();
}
#endif // OPK_LOG
void webusbPoll()
{
	// 160 B holds the largest command: a firmware-update data chunk 0x21 = [op][off u32][len][<=128 data]
	// = 134 B (spans USB-FS packets; the byte-wise accumulation below reassembles it). Next-largest are the
	// 0x0D bond-slot write (27 B) and the 0x12 lizard set-binding (18 B); everything else is <= 9 B.
	static uint8_t buf[160];
	static uint8_t n = 0;
	while (usb_web.available()) {
		int c = usb_web.read();
		if (c < 0)
			break;
		if (n < sizeof buf)
			buf[n++] = (uint8_t)c;
		// process complete commands from the front of buf
		for (;;) {
			if (n == 0)
				break;
			uint8_t op = buf[0];
			if ((op < 0x01 || op > 0x15) &&
			    (op < 0x20 || op > 0x25)) { // resync: drop one byte
				memmove(buf, buf + 1, --n);
				continue;
			}
			// 0x21 (fwup data) carries its own length at [5]; sanity-gate it BEFORE trusting it as a
			// command length so a corrupt byte can only cost a one-byte resync, never a stuck parser.
			if (op == 0x21 && n >= 6) {
				uint8_t dl = buf[5];
				if (dl == 0 || dl > 128 || (dl & 3)) {
					memmove(buf, buf + 1, --n);
					continue;
				}
			}
			// Command length (fixed per opcode). 0x0D = write-one-bond-slot (27 B); 0x12 = set-one-lizard-
			// binding (18 B); 0x05/0x0E/0x0F/0x10/0x13 carry one value byte; 0x02 a field+value; 0x0A a
			// 3-byte magic. Firmware update: 0x20 begin [size u32][crc32 u32], 0x21 data (6 B header +
			// payload), 0x22/0x23/0x24 bare. (0x11/0x14/0x15 are bare lizard opcodes -> default 1.)
			uint8_t need =
				(op == 0x0D) ? 27 :
				(op == 0x12) ? 18 :
				(op == 0x02) ? 3 :
				(op == 0x03 || op == 0x05 || op == 0x0E ||
				 op == 0x0F || op == 0x10 || op == 0x13) ?
					       2 :
				(op == 0x0A) ? 4 :
				(op == 0x25) ? 5 :
				(op == 0x20) ? 9 :
				(op == 0x21) ? (uint8_t)(6 + (n >= 6 ? buf[5] :
								       0)) :
					       1;
			if (n < need)
				break; // wait for more bytes
			if (boardCommand(op)) {
				memmove(buf, buf + need, n - need);
				n -= need;
				continue;
			}
			if (op == 0x01) {
				g_blobRequest =
					true; // sent from the usbd task (webusbSofDrain)
			}
			// 0x09: export all bond slots (clone backup). One 0xA7 frame, sent from the usbd task.
			else if (op == 0x09) {
				g_bondExportRequest = true;
			}
			// 0x0F: stability test on/off. Puck->controller haptics do NOT reset the controller's own
			// user-input idle auto-off (we already poll it every 4ms without keeping it awake), so instead
			// signal host-awake: enable the E7 announce (0xE7 00 00 = host-awake vs 00 01 = suspended, per
			// the RE) so the controller is told the host is active and (hopefully) doesn't power-save. The
			// 10s buzz stays -- it also exercises the haptic-relay path that correlates with the hang.
			else if (op == 0x0F) {
				g_stabTest = (buf[1] != 0);
				g_e7b = 0; // byte2=0 => host-awake
				g_e7announce = g_stabTest;
			}
			// 0x10: stream the saved flight-recorder trail (0xA8 frames). buf[1]=1 restarts (header + rewind),
			// buf[1]=0 continues the drain. Drained straight from loop context like the 0x06 capture drain --
			// webusbDrainFlight is drop-on-full so it never blocks. Always available (recorder isn't OPK_LOG).
			else if (op == 0x10) {
				webusbDrainFlight(buf[1] != 0);
			}
#if OPK_LOG

			// rewind drain: buf[1]=1 from boot (whole ring), 0 from now
			else if (op == 0x05) {
				hapLogResetDrain(buf[1] != 0);
			} else if (op == 0x06) {
				webusbDrainCapture();
			} // drain entries since the rewind (panel polls this)
#endif

			// clear a stuck/latched haptic buzz on the controller
			else if (op == 0x07) {
				hapticReinit();
			}

			// trigger controller power-off (same path Steam 0x9F / host-suspend use)
			else if (op == 0x08) {
				hapticSendShutdown();
			}

			// factory wipe: erase cfg.bin + bonds.bin, reboot to clean defaults.
			// Guarded by a 3-byte magic ("ERS") so a stray/corrupt byte can never trigger it.
			// Irreversible -- the controller must be re-paired afterwards.
			else if (op == 0x0A) {
				if (buf[1] == 0x45 && buf[2] == 0x52 &&
				    buf[3] == 0x53) {
					usb_web.flush();
					factoryErase();
					delay(40);
					faultDiagArmIntentionalReset();
					NVIC_SystemReset();
				}

				// reboot into serial DFU (adafruit-nrfutil)
			} else if (op == 0x0B) {
				usb_web.flush();
				delay(40);
				faultDiagArmIntentionalReset();
				enterSerialDfu();

				// reboot into UF2 bootloader (USB mass storage)
			} else if (op == 0x0C) {
				usb_web.flush();
				delay(40);
				faultDiagArmIntentionalReset();
				enterUf2Dfu();

				// 0x25: FULL BOARD WIPE (debug panel only). Erase the app + config/bond + bootloader-settings
				// flash and reboot app-less, so the board mounts as the UF2 drive on EVERY boot until it is
				// flashed again -- no trace of the firmware left. Distinct from 0x0A (factory reset, which
				// reformats settings but keeps the firmware). Guarded by the 4-byte magic "WIPE" so no stray
				// byte can ever trigger it. Irreversible without re-flashing.
			} else if (op == 0x25) {
				if (buf[1] == 0x57 && buf[2] == 0x49 &&
				    buf[3] == 0x50 && buf[4] == 0x45) {
					usb_web.flush();
					fwupArmFullWipe();
					delay(40);
					faultDiagArmIntentionalReset();
					NVIC_SystemReset();
				}

				// 0x0D: write ONE bond slot into RAM -- the "clone onto this puck" side of Export/Import.
				// [0x0D][slot][used][24 rec]. used=0 (or an empty record) clears the slot. The panel sends
				// one of these per slot, then a 0x0E to persist + reboot. Kept to a single small command
				// (<=27 B) so it never spans a USB packet, and acked with a status blob so the panel's
				// read-after-write keeps the OUT pipe flowing (same shape as the proven 0x02 setters).
			} else if (op == 0x0D) {
				uint8_t slot = buf[1], used = buf[2];
				if (slot < NSLOT) {
					if (used && !recEmpty(buf + 3)) {
						memcpy(g_slot[slot].rec,
						       buf + 3, 24);
						g_slot[slot].used = true;
					} else {
						memset(g_slot[slot].rec, 0, 24);
						g_slot[slot].used = false;
					}
				}
				g_blobRequest = true; // ack

				// 0x0E: commit an import -- persist the bond slots written by 0x0D, optionally apply a USB
				// mode ([0x0E][mode]; 0xFF = leave unchanged), then reboot so the RF session addresses
				// regenerate from the new bond UUIDs.
			} else if (op == 0x0E) {
				uint8_t mode = buf[1];
				saveBonds();
				usb_web.flush();
				// clean detach + reboot into `mode` (0xFF = keep current); regenerates RF
				// session addrs from the imported bonds and releases any held input.
				modeSwitchReboot(mode);

				// ---- lizard (desktop) binding map editor ----
				// Renumbered to 0x11..0x15 on the merge with main: main already owns 0x0D (bond-slot
				// write), 0x0E (import commit), 0x0F (stability test) and 0x10 (flight-recorder drain),
				// which the pre-merge branch had collided with. The panel JS uses the same 0x11..0x15.
				// 0x11: dump the current map as a 0xAA frame.
			} else if (op == 0x11) {
				webusbSendLizard();

				// 0x13 [count]: BEGIN a map edit -- set the binding count (clamped). The
				// panel then sends one 0x12 per binding (0..count-1) and a 0x14 to persist.
			} else if (op == 0x13) {
				g_lizardMap.count =
					(buf[1] <= LZ_MAX_BINDINGS) ?
						buf[1] :
						LZ_MAX_BINDINGS;

				// 0x12 [idx][outType][od0..6][trig LE4][hold LE4]: set one binding.
			} else if (op == 0x12) {
				uint8_t idx = buf[1];
				if (idx < LZ_MAX_BINDINGS) {
					LizardBinding &b =
						g_lizardMap.bindings[idx];
					b.outType = buf[2];
					for (int k = 0; k < 7; k++)
						b.outData[k] = buf[3 + k];
					b.trigMask = (uint32_t)buf[10] |
						     ((uint32_t)buf[11] << 8) |
						     ((uint32_t)buf[12] << 16) |
						     ((uint32_t)buf[13] << 24);
					b.holdMask = (uint32_t)buf[14] |
						     ((uint32_t)buf[15] << 8) |
						     ((uint32_t)buf[16] << 16) |
						     ((uint32_t)buf[17] << 24);
				}

				// 0x14: COMMIT the edited map to flash and echo it back.
			} else if (op == 0x14) {
				saveLizardMap();
				webusbSendLizard();

				// 0x15: reset the map to the built-in defaults, persist, echo back.
			} else if (op == 0x15) {
				defaultLizardMap();
				saveLizardMap();
				webusbSendLizard();

				// 0x20..0x24: staged firmware update (see fw_update.h). Each op is acked with an 0xAB
				// frame from the usbd task; the panel ping-pongs on those acks, so at most one command
				// is ever in flight (also what bounds the flash-stall per loop() pass to one page erase).
			} else if (op == 0x20) {
				uint32_t sz = (uint32_t)buf[1] |
					      ((uint32_t)buf[2] << 8) |
					      ((uint32_t)buf[3] << 16) |
					      ((uint32_t)buf[4] << 24);
				uint32_t crc = (uint32_t)buf[5] |
					       ((uint32_t)buf[6] << 8) |
					       ((uint32_t)buf[7] << 16) |
					       ((uint32_t)buf[8] << 24);
				fwupAckPost(fwupBegin(sz, crc));
			} else if (op == 0x21) {
				uint32_t off = (uint32_t)buf[1] |
					       ((uint32_t)buf[2] << 8) |
					       ((uint32_t)buf[3] << 16) |
					       ((uint32_t)buf[4] << 24);
				fwupAckPost(fwupChunk(off, buf + 6, buf[5]));
			} else if (op == 0x22) {
				fwupAckPost(fwupEnd());

				// 0x23: plain clean reboot. After a committed 0x22 the boot path applies the staged
				// image; unarmed it is just a normal restart.
			} else if (op == 0x23) {
				usb_web.flush();
				delay(40);
				faultDiagArmIntentionalReset();
				NVIC_SystemReset();

			} else if (op == 0x24) {
				fwupAbort();
				fwupAckPost(FWUP_OK);

			} else if (op == 0x02) {
				uint8_t f = buf[1], v = buf[2];

				// every settable field persists (poll rate is no longer settable)
				bool persist = true;
				// per-type cfg writes (protocol v10/v17): field = 40 + et*9 + k, k: 0..3 back, 4 qam, 5 abSwap,
				// 6 padHaptics, 7 ledBright, 8 rumble. Edits g_type[et]; refresh the live mirrors if it's the active type.
				if (f >= 40 && f < 40 + ET_COUNT * 9) {
					uint8_t et = (uint8_t)((f - 40) / 9),
						k = (uint8_t)((f - 40) % 9);
					if (et < ET_COUNT) {
						if (k < 4)
							g_type[et].back[k] = v;
						else if (k == 4)
							g_type[et].qamMap = v;
						else if (k == 5)
							g_type[et].abSwap =
								v ? 1 : 0;
						else if (k == 6)
							g_type[et].padHaptics =
								v ? 1 : 0;
						else if (k == 7)
							g_type[et].ledBright =
								v > 100 ? 100 :
									  v;
						else if (k == 8)
							g_type[et].rumble =
								v ? 1 : 0;
						if (et == g_etype)
							applyActiveType();
					}
					saveCfg();
					g_blobRequest = true;
					memmove(buf, buf + need, n - need);
					n -= need;
					continue;
				}
				switch (f) {
				case 1:
					g_mDiv = v < 4 ? 4 : v;
					break;
				case 2:
					g_mFric = v > 99 ? 99 : v;
					break;
				// case 3 (padSmooth) removed -- Steam-mode pad coords are forwarded raw; Steam does its own smoothing.
				// Legacy single-value fields (4 abSwap, 5-8 back, 21 qam) edit the ACTIVE emulated type.
				case 4:
					if (g_etype < ET_COUNT) {
						g_type[g_etype].abSwap = v ? 1 :
									     0;
						applyActiveType();
					}
					break;
				case 5:
				case 6:
				case 7:
				case 8:
					if (g_etype < ET_COUNT) {
						g_type[g_etype].back[f - 5] = v;
						applyActiveType();
					}
					break;
				// case 9 (pollU100) removed -- poll rate is fixed at POLL_US_DEFAULT and no longer configurable.

				// E7 protocol-version B-byte (experimental v1 fast)
				case 10:
					g_e7b = v ? 1 : 0;
					break;

				// haptic-relay opcode
				case 11:
					g_relayOp = v;
					break;

				// haptic-relay sub-type
				case 12:
					g_relaySub = v;
					break;
				case 13:
					g_testHaptic = v ? v : 40;
					break; // inject v test haptics (0->40)

				// Steam: forward only fresh reports (dedupe)
				case 14:
					g_fwdNewOnly = v ? 1 : 0;
					break;
				case 15:
					g_qos = v ? 1 : 0;
					g_hopIdx = 0;
					g_qosBad = 0;
					g_qosCheckMs = millis();
					break; // QoS adaptive channel hopping

				// persist last mode across reboots (else always boot Steam)
				case 16:
					g_persistMode = v ? true : false;
					break;

				// back4+B/X/Y mode assignments
				case 17:
				case 18:
				case 19:
					if (modeValid(v))
						g_chordBtn[f - 17] = v;
					break;

				// back4+D-pad mode assignments (left/up/right/down), protocol v18
				case 34:
				case 35:
				case 36:
				case 37:
					if (modeValid(v))
						g_chordDpad[f - 34] = v;
					break;

				// reboot once WITH the CDC serial console (puck mode), then auto-revert
				case 20:
					armDebugCdcNextBoot();
					usb_web.flush();
					delay(40);
					faultDiagArmIntentionalReset();
					NVIC_SystemReset();
					break;

				// QAM physical button remap code (0=default/unmapped) -- active emulated type
				case 21:
					if (g_etype < ET_COUNT) {
						g_type[g_etype].qamMap = v;
						applyActiveType();
					}
					break;

				// 80..87: per-type trackpad->stick mapping, field = 80 + et*2 + pad
				// (pad 0 = left, 1 = right; value PS_OFF/PS_LEFT/PS_RIGHT).
				// Must stay clear of the per-type cfg range 40..40+ET_COUNT*9-1
				// (40..75), which is claimed before this switch runs.
				case 80:
				case 81:
				case 82:
				case 83:
				case 84:
				case 85:
				case 86:
				case 87: {
					uint8_t et = (uint8_t)((f - 80) / 2),
						pad = (uint8_t)((f - 80) % 2);
					if (et < ET_COUNT && v <= PS_MAX) {
						g_padStickCfg[et][pad] = v;
						if (et == g_etype)
							applyActiveType();
					}
					break;
				}

				// Switch Pro gyro mapping: 0 = corrected (default), 1 = legacy
				// (pre-#189 raw axes, no sensitivity trim). Protocol v19.
				case 38:
					g_swGyroLegacy = v ? 1 : 0;
					swProSaveCfg();
					persist = false;
					break;

					// (field 22, rumble strength, removed -- fixed at RUMBLE_SCALE_PCT)
					// (fields 23/24, Switch Pro report rate + gyro scale, removed -- rate is
					//  fixed at full and the gyro mapping is now field 38)
					// (field 25, poll RX window, removed -- g_rxWin is now FIXED/not configurable)
					// (fields 27/28, post-connect haptic block, removed -- permanently disabled)

				// Used to be experimental g_landAll87. Persisted; blob p[181] reflects state. Now ignored.
				case 29:
					// g_landAll87 = v ? 1 : 0;
					break;
				}
				if (persist)
					saveCfg();
				g_blobRequest = true;
			} else if (op == 0x03) {
				uint8_t m = buf[1];
				if (modeValid(m) && !USBDevice.suspended()) {
					// best-effort status to the panel before the reboot; the SOF drain
					// sends it during the flush below (no blocking flush on loop()).
					g_blobRequest = true;
					usb_web.flush();
					// clean detach + reboot (releases held input on the outgoing device)
					modeSwitchReboot(m);
				}
			}
			memmove(buf, buf + need, n - need);
			n -= need;
		}
	}
}