OpenPuck/docs/BUILD_AND_DEPLOY.md

Build And Deploy

These instructions cover firmware builds for macOS, Linux, and Windows, plus static hosting of the WebUSB app through GitHub Pages.

1. Prerequisites

Hardware:

• nRF52840 board supported by the Adafruit nRF52 Arduino core
• USB cable
• Steam Controller 2 controller

Software:

• arduino-cli
• Adafruit nRF52 Arduino core
• adafruit-nrfutil (Python package, for DFU packaging — see §4)
• Chrome or Edge for the WebUSB app

2. Install Arduino CLI

macOS

brew install arduino-cli

Linux

Use your package manager if it ships a recent arduino-cli, or download the release archive from Arduino and place arduino-cli on PATH.

Windows

Use choco and do a choco install arduino-cli. If you don't have that then install the official Arduino CLI zip or MSI, then ensure arduino-cli.exe is on PATH.

3. Install the board core

Run once on any platform:

pip install adafruit-nrfutil         # DFU packaging helper (required by the Adafruit nRF52 build recipe)
arduino-cli config init
arduino-cli core update-index
arduino-cli core install adafruit:nrf52 --additional-urls https://adafruit.github.io/arduino-board-index/package_adafruit_index.json

4. Build the firmware

From the repository root:

./gen_version.sh   # optional: stamp the build with the current git hash + dirty flag (shown in the panel)
arduino-cli compile -b adafruit:nrf52:feather52840 --build-property "build.extra_flags=-DNRF52840_XXAA {build.flags.usb} -DCFG_TUD_HID=4" OpenPuck

This sketch requires CFG_TUD_HID=4 because Steam mode exposes four HID interfaces.

Build provenance. gen_version.sh writes OpenPuck/git_version.h with the current commit's short hash and a dirty flag (1 if the working tree has any tracked change or untracked file). The firmware bakes these in and reports them over WebUSB, so the panel's Build (git) field shows exactly which commit is flashed and whether it was a clean checkout — handy for confirming what's on a board. The header is git-ignored; if you skip the script the build still succeeds and the panel shows unknown. You can also inject the values directly instead of using the script, e.g. append -DOPK_GIT_HASH=\"$(git rev-parse --short=8 HEAD)\" -DOPK_GIT_DIRTY=0 to build.extra_flags.

5. Upload the firmware

macOS / Linux

Find the board port:

arduino-cli board list

Upload:

arduino-cli upload \
  -b adafruit:nrf52:feather52840 \
  -p /dev/ttyACM0 \
  OpenPuck

Replace /dev/ttyACM0 with the actual port. On macOS it is usually /dev/cu.usbmodem*.

Windows

Find the COM port:

arduino-cli board list

Upload:

arduino-cli upload `
  -b adafruit:nrf52:feather52840 `
  -p COM5 `
  OpenPuck

Replace COM5 with the actual board port.

5b. Upload via DFU (nRF52840 UF2 bootloader)

If the board has the Adafruit nRF52 UF2 bootloader (common on Pro Micro nRF52840 boards), you can upload by dragging the compiled .uf2 file onto the board's mass-storage volume:

1. Double-tap the RST button (or use arduino-cli upload once via serial to trigger the bootloader, then immediately hold the button). The board mounts as a UF2BOOT / NRF52BOOT drive.

2. Locate the compiled .uf2 file:

   # After a successful `arduino-cli compile`, find the .uf2 in the build directory:
   ls /tmp/arduino/cores/adafruit_nrf52_adafruit52840/*.uf2
   # or, on Windows, look in %TEMP%\arduino\...
   

3. Copy the .uf2 file onto the UF2BOOT drive. The board auto-ejects and reboots with the new firmware.

Alternatively, use the adafruit-nrfutil DFU Python tool with the board in DFU mode (bootloader LED pulsing):

# Enter DFU mode (double-tap RST). On Linux/macOS:
adafruit-nrfutil --verbose dfu serial --package OpenPuck/OpenPuck.ino.adafruit_nrf52_feather52840.zip -p /dev/ttyACM0 -b 115200

# On Windows (PowerShell):
adafruit-nrfutil --verbose dfu serial --package OpenPuck/OpenPuck.ino.adafruit_nrf52_feather52840.zip -p COM5 -b 115200

Replace the port (/dev/ttyACM0 / COM5) with the actual board port.

Note: The .zip package is generated automatically by arduino-cli compile when the Adafruit nRF52 core is used. If it is missing, ensure adafruit-nrfutil is installed and recompile.

6. Factory reset (erase persistent storage)

Re-flashing firmware does not erase the board's internal LittleFS. The paired-controller bond (bonds.bin) and every saved setting (cfg.bin: USB mode, chord assignments, back-paddle map, mouse sensitivity) survive a fresh build and upload. To bring a board up in a truly clean state — a new unit, a hand-me-down with a stale bond, or a corrupted config — wipe the filesystem with one of:

• Recovery build (-DOPK_FACTORY_RESET=1): a firmware that wipes all persistent storage once, on the first boot after flashing, then behaves like a normal build that persists settings. Use it to recover a board from a bad config/bond without a console or panel:

  ./gen_version.sh   # recommended: gives the build a distinct git hash (see below)
  arduino-cli compile -b adafruit:nrf52:feather52840 --build-property "build.extra_flags=-DNRF52840_XXAA {build.flags.usb} -DCFG_TUD_HID=4 -DOPK_FACTORY_RESET=1" OpenPuck
  

It is not a wipe-every-boot image: after the one-time reset it stamps a tag file with the build's git hash, so subsequent boots skip the wipe and persist normally. Flashing this same image again won't re-wipe (the tag matches); flashing a different build (different git hash) re-triggers the one-time reset. For an on-demand wipe at any time, use the WebUSB button or serial ERASE-ALL below. Re-pair the controller after a reset.

• WebUSB panel (any mode): open the panel (§8), and in the maintenance card click ⚠ Factory erase. Confirm the two warning dialogs and type ERASE when prompted. The board reformats its filesystem and reboots to factory defaults. This works in every USB mode.
• Serial console (CDC): connect to the board's serial port at 115200 baud and send the line ERASE-ALL (exact, all caps). Same effect: reformat + reboot.

Both reformat the entire internal filesystem (cfg.bin + bonds.bin and anything else), so the action is irreversible and the controller must be re-paired afterwards (see §7).

Note on the serial method: puck (Steam/Lizard) mode drops the CDC console by default to free a USB endpoint for the wake-mouse interface, so the serial port may not be present in that mode. Either arm the one-shot debug CDC first (panel debug-CDC toggle / D console command, which keeps the console for the next boot), or just use the WebUSB Factory erase button, which is available in all modes.

7. Pair and verify

1. Flash the board.
2. Plug it into the host.
3. In Steam mode it enumerates as a puck-compatible device.
4. Pair the controller to one of the bond slots.
5. Verify that the slot returns 0xB4 = 0x02 when connected.

8. Run the WebUSB app locally

WebUSB requires a secure context. http://localhost qualifies.

macOS / Linux

cd docs
python3 -m http.server 8008

Open:

http://localhost:8008

Windows

cd docs
py -m http.server 8008

Open:

http://localhost:8008

9. Known operational details

• Chrome or Edge is required for WebUSB.
• The board re-enumerates on USB mode switches.
• Poll interval tuning in the WebUSB app is session-only by design.
• Bonds persist in the board's internal filesystem.