OpenPuck/Makefile

# OpenPuck developer convenience targets.

# Pin to clang-format 18 to match CI; output differs between versions, so a
# mismatch would make CI reject locally-formatted code. Resolve the binary in
# order of preference: the apt-style versioned name (CI / Linux), the Homebrew
# llvm@18 keg (macOS), then a bare clang-format as a last resort. Override with
# `make format CLANG_FORMAT=/path/to/clang-format` if yours lives elsewhere.
CLANG_FORMAT ?= $(shell command -v clang-format-18 \
	|| ([ -x /opt/homebrew/opt/llvm@18/bin/clang-format ] && echo /opt/homebrew/opt/llvm@18/bin/clang-format) \
	|| ([ -x /usr/local/opt/llvm@18/bin/clang-format ] && echo /usr/local/opt/llvm@18/bin/clang-format) \
	|| command -v clang-format)

# All hand-written C/C++ sources. Generated headers (git_version.h) are
# gitignored and excluded here so formatting never touches them.
FORMAT_FILES := $(shell find OpenPuck ReversePuckFirmware puck_sniffer pairtui \
	\( -name '*.c' -o -name '*.cpp' -o -name '*.h' -o -name '*.hpp' -o -name '*.ino' \) \
	-not -name 'git_version.h')

# --- firmware build ---------------------------------------------------------
# The OpenPuck firmware needs two TinyUSB config values that differ from the Adafruit nRF52 core defaults:
#   CFG_TUD_HID=6            -- four HID interfaces (Steam mode exposes four puck slots) plus one for mouse 
#								and one for WebUSB; core default is 2.
#   CFG_TUD_TASK_QUEUE_SZ=64 -- deeper usbd event queue; the default 16 deadlocks the loop task under comms
#                               load -> watchdog reset (see OpenPuck.ino + docs/BUILD_AND_DEPLOY.md).
#   CFG_TUD_VENDOR_TX_BUFSIZE=256 -- the WebUSB status blob is ~118 B; the core default 64 can't hold it whole,
#                               so the panel send (which drops rather than blocks when the FIFO is full) could
#                               never fit a frame -> blank panel. Sized to hold a full blob with headroom.
# They're baked in here so a normal build is just `make build` -- no need to remember the flags. Override any
# on the command line, e.g.   make build CFG_TUD_HID=8 CFG_TUD_TASK_QUEUE_SZ=128
# or add your own defines:     make build EXTRA_FLAGS="-DOPK_LOG=1"
FQBN ?= adafruit:nrf52:feather52840
CFG_TUD_HID ?= 6
# Optional output paths; when set, --clean is implied and build artifacts land in OUTPUT_DIR.
# Used by CI: make build BUILD_PATH=build/cache/openpuck OUTPUT_DIR=build/openpuck
BUILD_PATH ?=
OUTPUT_DIR ?=
# Deep so a loop()-context sendReport never blocks on a full usbd event queue (the watchdog path). Sends run
# from loop() now (usbTxPump) for stable RF timing, so this depth is what keeps that block from happening.
CFG_TUD_TASK_QUEUE_SZ ?= 512
# Must hold a whole WebUSB status blob (~118 B) so the drop-on-full panel send can fit one; core default 64 is
# too small and would silently drop every frame (blank panel / stale mappings).
CFG_TUD_VENDOR_TX_BUFSIZE ?= 256
EXTRA_FLAGS ?=
# {build.flags.usb} is expanded by arduino-cli (VID/PID/strings); pass it through verbatim.
USB_EXTRA_FLAGS = -DNRF52840_XXAA {build.flags.usb} -DCFG_TUD_HID=$(CFG_TUD_HID) -DCFG_TUD_TASK_QUEUE_SZ=$(CFG_TUD_TASK_QUEUE_SZ) -DCFG_TUD_VENDOR_TX_BUFSIZE=$(CFG_TUD_VENDOR_TX_BUFSIZE) $(EXTRA_FLAGS)
# When BUILD_PATH is set, --clean + path flags are injected; omitted for fast incremental dev builds.
_PATH_FLAGS = $(if $(BUILD_PATH),--clean --build-path $(BUILD_PATH) --output-dir $(OUTPUT_DIR))

# `flash`/`deploy` take the serial port as a REQUIRED POSITIONAL arg: `make flash /dev/cu.usbmodem1101`.
# (No auto-detect -- uploading to a guessed serial port risks writing to the wrong device. List with
# `arduino-cli board list`.) FLASH_PORT = whatever goal isn't one of our real targets; the catch-all rule at
# the bottom swallows it so make doesn't try to build the port path as a target.
FLASH_PORT := $(filter-out format format-check check build build-raytac \
	package-raytac flash-raytac deploy-raytac provision-raytac-softdevice \
	build-recovery reversepuck reversepuck-flash reversepuck-deploy flash deploy,$(MAKECMDGOALS))
UPLOAD = arduino-cli upload -b $(FQBN) -p "$(FLASH_PORT)" OpenPuck

# ReversePuck (controller dongle, 28DE:1302) build flags. It has ONE HID interface (core default 2 is fine),
# so it doesn't need CFG_TUD_HID; it DOES need the deeper vendor TX FIFO to hold the 0xAC paired-pucks list
# whole, and the deeper usbd task queue keeps loop()-context WebUSB/CDC/HID sends off the watchdog path.
RP_USB_FLAGS = -DNRF52840_XXAA {build.flags.usb} -DCFG_TUD_TASK_QUEUE_SZ=$(CFG_TUD_TASK_QUEUE_SZ) -DCFG_TUD_VENDOR_TX_BUFSIZE=$(CFG_TUD_VENDOR_TX_BUFSIZE) $(EXTRA_FLAGS)
RP_UPLOAD = arduino-cli upload -b $(FQBN) -p "$(FLASH_PORT)" ReversePuckFirmware

.PHONY: format format-check check build build-raytac package-raytac \
	flash-raytac deploy-raytac provision-raytac-softdevice build-recovery \
	reversepuck reversepuck-flash reversepuck-deploy flash deploy

## Compile the firmware with the required USB flags baked in. Override CFG_TUD_HID / CFG_TUD_TASK_QUEUE_SZ /
## EXTRA_FLAGS / FQBN as make variables if needed.
build:
	arduino-cli compile -b $(FQBN) $(_PATH_FLAGS) --build-property "build.extra_flags=$(USB_EXTRA_FLAGS)" OpenPuck

## Build for the Raytac MDBT50Q-CX-40 without replacing its Open DFU bootloader.
## Like `build`, this does NOT run gen_version.sh -- run it yourself first if you want version provenance
## baked in. (It must not run here: CI generates git_version.h once with OPK_BUILD_VERSION set, and a
## regeneration mid-workflow would strip the release version out of every build that follows.)
build-raytac:
	mkdir -p build/raytac build/cache/raytac
	arduino-cli compile --clean -b adafruit:nrf52:mdbt50qrx \
		--build-path build/cache/raytac \
		--output-dir build/raytac \
		--build-property "build.extra_flags=$(USB_EXTRA_FLAGS) -DOPK_BOARD_MDBT50Q_CX_40=1" OpenPuck

## Package an existing Raytac build for its factory Nordic Open DFU bootloader.
package-raytac:
	@test -f build/raytac/OpenPuck.ino.hex || { \
		echo "run 'make build-raytac' first"; exit 1; }
	$(RM) build/raytac/OpenPuck-mdbt50q-cx-40.zip
	nrfutil nrf5sdk-tools pkg generate --hw-version 52 --sd-req 0xB6 \
		--application-version 1 \
		--application build/raytac/OpenPuck.ino.hex \
		build/raytac/OpenPuck-mdbt50q-cx-40.zip

## Program the application package with the device in physical Open DFU mode.
flash-raytac:
	@test -f build/raytac/OpenPuck-mdbt50q-cx-40.zip || { \
		echo "run 'make package-raytac' first"; exit 1; }
	nrfutil device program \
		--firmware build/raytac/OpenPuck-mdbt50q-cx-40.zip \
		--traits nordicDfu

## Build, package, and program the application without changing the SoftDevice.
deploy-raytac:
	$(MAKE) build-raytac
	$(MAKE) package-raytac
	$(MAKE) flash-raytac

## One-time S140 6.1.1 provisioning; re-enter Open DFU before flashing the app.
provision-raytac-softdevice:
	@test -f "$(SOFTDEVICE_HEX)" || { \
		echo "set SOFTDEVICE_HEX to Nordic's S140 6.1.1 HEX"; \
		exit 1; }
	mkdir -p build/raytac
	$(RM) build/raytac/s140-6.1.1.zip
	nrfutil nrf5sdk-tools pkg generate --hw-version 52 \
		--sd-req 0xAE,0xB6 --sd-id 0xB6 \
		--softdevice "$(SOFTDEVICE_HEX)" \
		build/raytac/s140-6.1.1.zip
	nrfutil device program --firmware build/raytac/s140-6.1.1.zip \
		--traits nordicDfu

## One-time factory-reset recovery image (wipes persistent storage once on first boot). See §6 of the build doc.
build-recovery:
	$(MAKE) build BUILD_PATH=$(BUILD_PATH) OUTPUT_DIR=$(OUTPUT_DIR) EXTRA_FLAGS="$(EXTRA_FLAGS) -DOPK_FACTORY_RESET=1"

## Compile the ReversePuck controller dongle firmware (28DE:1302) with its WebUSB vendor flags baked in.
reversepuck:
	arduino-cli compile -b $(FQBN) $(_PATH_FLAGS) --build-property "build.extra_flags=$(RP_USB_FLAGS)" ReversePuckFirmware

## Upload the most recent ReversePuck build. Usage: make reversepuck-flash <port>
reversepuck-flash:
	@[ -n "$(FLASH_PORT)" ] || { echo "usage: make reversepuck-flash <port>   e.g. make reversepuck-flash /dev/cu.usbmodem1101"; exit 1; }
	$(RP_UPLOAD)

## Build then upload the ReversePuck dongle in one step. Usage: make reversepuck-deploy <port>
reversepuck-deploy:
	@[ -n "$(FLASH_PORT)" ] || { echo "usage: make reversepuck-deploy <port>   e.g. make reversepuck-deploy /dev/cu.usbmodem1101"; exit 1; }
	$(MAKE) reversepuck BUILD_PATH=$(BUILD_PATH) OUTPUT_DIR=$(OUTPUT_DIR)
	$(RP_UPLOAD)

## Upload the most recent build. Usage: make flash <port>   e.g.  make flash /dev/cu.usbmodem1101
## The board may need DFU/bootloader mode first (double-tap RST): puck (Steam/Lizard) mode drops the CDC port
## so arduino-cli can't auto-reset it -- see docs/BUILD_AND_DEPLOY.md.
flash:
	@[ -n "$(FLASH_PORT)" ] || { echo "usage: make flash <port>   e.g. make flash /dev/cu.usbmodem1101   (list ports: arduino-cli board list)"; exit 1; }
	$(UPLOAD)

## Build then upload in one step. Usage: make deploy <port>   (same build overrides as `build`).
deploy:
	@[ -n "$(FLASH_PORT)" ] || { echo "usage: make deploy <port>   e.g. make deploy /dev/cu.usbmodem1101"; exit 1; }
	$(MAKE) build BUILD_PATH=$(BUILD_PATH) OUTPUT_DIR=$(OUTPUT_DIR)
	$(UPLOAD)

# Swallow the positional <port> arg so make doesn't error trying to build it as a target. Scoped to things
# that look like a serial port (so a real typo like `make buld` still errors instead of silently no-op'ing).
/dev/% COM% tty% cu.%:
	@:

## Reformat all C/C++ sources in place using the Linux kernel style.
format:
	$(CLANG_FORMAT) -i $(FORMAT_FILES)

## Verify all C/C++ sources are formatted; exit non-zero if any differ.
## Used by CI to reject unformatted code.
format-check:
	$(CLANG_FORMAT) --dry-run --Werror $(FORMAT_FILES)

## Everything CI gates on.
check: format-check