mtk-lk/platform/mt6580/ncp1854.c

/* Copyright Statement:
*
* This software/firmware and related documentation ("MediaTek Software") are
* protected under relevant copyright laws. The information contained herein
* is confidential and proprietary to MediaTek Inc. and/or its licensors.
* Without the prior written permission of MediaTek inc. and/or its licensors,
* any reproduction, modification, use or disclosure of MediaTek Software,
* and information contained herein, in whole or in part, shall be strictly prohibited.
*/
/* MediaTek Inc. (C) 2015. All rights reserved.
*
* BY OPENING THIS FILE, RECEIVER HEREBY UNEQUIVOCALLY ACKNOWLEDGES AND AGREES
* THAT THE SOFTWARE/FIRMWARE AND ITS DOCUMENTATIONS ("MEDIATEK SOFTWARE")
* RECEIVED FROM MEDIATEK AND/OR ITS REPRESENTATIVES ARE PROVIDED TO RECEIVER ON
* AN "AS-IS" BASIS ONLY. MEDIATEK EXPRESSLY DISCLAIMS ANY AND ALL WARRANTIES,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT.
* NEITHER DOES MEDIATEK PROVIDE ANY WARRANTY WHATSOEVER WITH RESPECT TO THE
* SOFTWARE OF ANY THIRD PARTY WHICH MAY BE USED BY, INCORPORATED IN, OR
* SUPPLIED WITH THE MEDIATEK SOFTWARE, AND RECEIVER AGREES TO LOOK ONLY TO SUCH
* THIRD PARTY FOR ANY WARRANTY CLAIM RELATING THERETO. RECEIVER EXPRESSLY ACKNOWLEDGES
* THAT IT IS RECEIVER'S SOLE RESPONSIBILITY TO OBTAIN FROM ANY THIRD PARTY ALL PROPER LICENSES
* CONTAINED IN MEDIATEK SOFTWARE. MEDIATEK SHALL ALSO NOT BE RESPONSIBLE FOR ANY MEDIATEK
* SOFTWARE RELEASES MADE TO RECEIVER'S SPECIFICATION OR TO CONFORM TO A PARTICULAR
* STANDARD OR OPEN FORUM. RECEIVER'S SOLE AND EXCLUSIVE REMEDY AND MEDIATEK'S ENTIRE AND
* CUMULATIVE LIABILITY WITH RESPECT TO THE MEDIATEK SOFTWARE RELEASED HEREUNDER WILL BE,
* AT MEDIATEK'S OPTION, TO REVISE OR REPLACE THE MEDIATEK SOFTWARE AT ISSUE,
* OR REFUND ANY SOFTWARE LICENSE FEES OR SERVICE CHARGE PAID BY RECEIVER TO
* MEDIATEK FOR SUCH MEDIATEK SOFTWARE AT ISSUE.
*/

#include <platform/mt_typedefs.h>
#include <platform/mt_reg_base.h>
#include <platform/mt_i2c.h>
#include <platform/mt_gpio.h>
#include <platform/mt_pmic.h>
#include <platform/ncp1854.h>
#include <printf.h>

#if !defined(CONFIG_POWER_EXT)
#include <platform/upmu_common.h>
#endif

int g_ncp1854_log_en = 0;

#define I2C_SWITCHING_CHARGER_CHANNEL 3
#define DISABLE_NCP1854_FACTORY_MODE

/**********************************************************
  *
  *   [I2C Slave Setting]
  *
  *********************************************************/
#define NCP1854_SLAVE_ADDR_WRITE	0x6C
#define NCP1854_SLAVE_ADDR_READ	0x6D

/**********************************************************
  *
  *   [Global Variable]
  *
  *********************************************************/
#define NCP1854_REG_NUM 18

#ifdef I2C_SWITCHING_CHARGER_CHANNEL
#define NCP1854_BUSNUM I2C_SWITCHING_CHARGER_CHANNEL
#else
#define NCP1854_BUSNUM 3
#endif

#define PRECC_BATVOL 2800	/* preCC 2.8V */

/* #ifndef GPIO_SWCHARGER_EN_PIN
#define GPIO_SWCHARGER_EN_PIN 65
#endif  */
kal_uint8 ncp1854_reg[NCP1854_REG_NUM] = { 0 };


/**********************************************************
  *
  *   [I2C Function For Read/Write ncp1854]
  *
  *********************************************************/
static struct mt_i2c_t ncp1854_i2c;

kal_uint32 ncp1854_write_byte(kal_uint8 addr, kal_uint8 value)
{
	kal_uint32 ret_code = I2C_OK;
	kal_uint8 write_data[2];
	kal_uint16 len;

	write_data[0] = addr;
	write_data[1] = value;

	ncp1854_i2c.id = NCP1854_BUSNUM;
	/* Since i2c will left shift 1 bit, we need to set NCP1854 I2C address to >>1 */
	ncp1854_i2c.addr = (NCP1854_SLAVE_ADDR_WRITE >> 1);
	ncp1854_i2c.mode = ST_MODE;
	ncp1854_i2c.speed = 100;
	len = 2;

	ret_code = i2c_write(&ncp1854_i2c, write_data, len);

	if (I2C_OK != ret_code)
		dprintf(INFO, "%s: i2c_write: ret_code: %d\n", __func__, ret_code);

	return ret_code;
}

kal_uint32 ncp1854_read_byte(kal_uint8 addr, kal_uint8 *dataBuffer)
{
	kal_uint32 ret_code = I2C_OK;
	kal_uint16 len;
	*dataBuffer = addr;

	ncp1854_i2c.id = NCP1854_BUSNUM;
	/* Since i2c will left shift 1 bit, we need to set NCP1854 I2C address to >>1 */
	ncp1854_i2c.addr = (NCP1854_SLAVE_ADDR_READ >> 1);
	ncp1854_i2c.mode = ST_MODE;
	ncp1854_i2c.speed = 100;
	len = 1;

	ret_code = i2c_write_read(&ncp1854_i2c, dataBuffer, len, len);

	if (I2C_OK != ret_code)
		dprintf(INFO, "%s: i2c_read: ret_code: %d\n", __func__, ret_code);

	return ret_code;
}


/**********************************************************
  *
  *   [Read / Write Function]
  *
  *********************************************************/
kal_uint32 ncp1854_read_interface(kal_uint8 RegNum, kal_uint8 *val, kal_uint8 MASK,
				  kal_uint8 SHIFT)
{
	kal_uint8 ncp1854_reg = 0;
	int ret = 0;

	dprintf(INFO, "--------------------------------------------------\n");

	ret = ncp1854_read_byte(RegNum, &ncp1854_reg);
	dprintf(INFO, "[ncp1854_read_interface] Reg[%x]=0x%x\n", RegNum, ncp1854_reg);

	ncp1854_reg &= (MASK << SHIFT);
	*val = (ncp1854_reg >> SHIFT);
	dprintf(INFO, "[ncp1854_read_interface] Val=0x%x\n", *val);

	return ret;

}

kal_uint32 ncp1854_config_interface(kal_uint8 RegNum, kal_uint8 val, kal_uint8 MASK,
				    kal_uint8 SHIFT)
{
	kal_uint8 ncp1854_reg = 0;
	int ret = 0;

	dprintf(INFO, "--------------------------------------------------\n");

	ret = ncp1854_read_byte(RegNum, &ncp1854_reg);
	/* dprintf(INFO, "[ncp1854_config_interface] Reg[%x]=0x%x\n", RegNum, ncp1854_reg); */

	ncp1854_reg &= ~(MASK << SHIFT);
	ncp1854_reg |= (val << SHIFT);

	if (RegNum == NCP1854_CON1 && val == 1 && MASK == CON1_REG_RST_MASK
	    && SHIFT == CON1_REG_RST_SHIFT) {
		/* RESET bit */
	} else if (RegNum == NCP1854_CON1) {
		ncp1854_reg &= ~0x80;	/* RESET bit read returs 1, so clear it */
	}

	ret = ncp1854_write_byte(RegNum, ncp1854_reg);
	/* dprintf(INFO, "[ncp18546_config_interface] Write Reg[%x]=0x%x\n", RegNum, ncp1854_reg); */

	/* Check */
	/* ncp1854_read_byte(RegNum, &ncp1854_reg); */
	/* dprintf(INFO, "[ncp1854_config_interface] Check Reg[%x]=0x%x\n", RegNum, ncp1854_reg); */

	return ret;

}

/**********************************************************
  *
  *   [ncp1854 Function]
  *
  *********************************************************/
/* CON0 */
kal_uint32 ncp1854_get_chip_status(void)
{
	kal_uint32 ret = 0;
	kal_uint8 val = 0;

	ret = ncp1854_read_interface((kal_uint8) (NCP1854_CON0),
				     (&val),
				     (kal_uint8) (CON0_STATE_MASK), (kal_uint8) (CON0_STATE_SHIFT)
	    );
	return val;
}

kal_uint32 ncp1854_get_batfet(void)
{
	kal_uint32 ret = 0;
	kal_uint8 val = 0;

	ret = ncp1854_read_interface((kal_uint8) (NCP1854_CON0),
				     (&val),
				     (kal_uint8) (CON0_BATFET_MASK), (kal_uint8) (CON0_BATFET_SHIFT)
	    );
	return val;
}

kal_uint32 ncp1854_get_statint(void)
{
	kal_uint32 ret = 0;
	kal_uint8 val = 0;

	ret = ncp1854_read_interface((kal_uint8) (NCP1854_CON0),
				     (&val),
				     (kal_uint8) (CON0_STATINT_MASK),
				     (kal_uint8) (CON0_STATINT_SHIFT)
	    );
	return val;
}

kal_uint32 ncp1854_get_faultint(void)
{
	kal_uint32 ret = 0;
	kal_uint8 val = 0;

	ret = ncp1854_read_interface((kal_uint8) (NCP1854_CON0),
				     (&val),
				     (kal_uint8) (CON0_FAULTINT_MASK),
				     (kal_uint8) (CON0_FAULTINT_SHIFT)
	    );
	return val;
}

/* CON1 */
void ncp1854_set_reset(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON1),
				       (kal_uint8) (val),
				       (kal_uint8) (CON1_REG_RST_MASK),
				       (kal_uint8) (CON1_REG_RST_SHIFT)
	    );
}

void ncp1854_set_chg_en(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON1),
				       (kal_uint8) (val),
				       (kal_uint8) (CON1_CHG_EN_MASK),
				       (kal_uint8) (CON1_CHG_EN_SHIFT)
	    );
}

void ncp1854_set_otg_en(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON1),
				       (kal_uint8) (val),
				       (kal_uint8) (CON1_OTG_EN_MASK),
				       (kal_uint8) (CON1_OTG_EN_SHIFT)
	    );
	return val;
}

kal_uint32 ncp1854_get_otg_en(void)
{
	kal_uint32 ret = 0;
	kal_uint8 val = 0;

	ret = ncp1854_read_interface((kal_uint8) (NCP1854_CON1),
				     (&val),
				     (kal_uint8) (CON1_OTG_EN_MASK), (kal_uint8) (CON1_OTG_EN_SHIFT)
	    );
	return val;
}

void ncp1854_set_fctry_mode(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON1),
				       (kal_uint8) (val),
				       (kal_uint8) (CON1_FCTRY_MOD_MASK),
				       (kal_uint8) (CON1_FCTRY_MOD_SHIFT)
	    );
}

void ncp1854_set_tj_warn_opt(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON1),
				       (kal_uint8) (val),
				       (kal_uint8) (CON1_TJ_WARN_OPT_MASK),
				       (kal_uint8) (CON1_TJ_WARN_OPT_SHIFT)
	    );
}

kal_uint32 ncp1854_get_usb_cfg(void)
{
	kal_uint32 ret = 0;
	kal_uint8 val = 0;

	ret = ncp1854_read_interface((kal_uint8) (NCP1854_CON1),
				     (&val),
				     (kal_uint8) (CON1_USB_CFG_MASK),
				     (kal_uint8) (CON1_USB_CFG_SHIFT)
	    );
	return val;
}

void ncp1854_set_tchg_rst(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON1),
				       (kal_uint8) (val),
				       (kal_uint8) (CON1_TCHG_RST_MASK),
				       (kal_uint8) (CON1_TCHG_RST_SHIFT)
	    );
}

void ncp1854_set_int_mask(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON1),
				       (kal_uint8) (val),
				       (kal_uint8) (CON1_INT_MASK_MASK),
				       (kal_uint8) (CON1_INT_MASK_SHIFT)
	    );
}

/* CON2 */
void ncp1854_set_wdto_dis(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON2),
				       (kal_uint8) (val),
				       (kal_uint8) (CON2_WDTO_DIS_MASK),
				       (kal_uint8) (CON2_WDTO_DIS_SHIFT)
	    );
}

void ncp1854_set_chgto_dis(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON2),
				       (kal_uint8) (val),
				       (kal_uint8) (CON2_CHGTO_DIS_MASK),
				       (kal_uint8) (CON2_CHGTO_DIS_SHIFT)
	    );
}

void ncp1854_set_pwr_path(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON2),
				       (kal_uint8) (val),
				       (kal_uint8) (CON2_PWR_PATH_MASK),
				       (kal_uint8) (CON2_PWR_PATH_SHIFT)
	    );
}

void ncp1854_set_trans_en(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON2),
				       (kal_uint8) (val),
				       (kal_uint8) (CON2_TRANS_EN_MASK),
				       (kal_uint8) (CON2_TRANS_EN_SHIFT)
	    );
}

void ncp1854_set_iinset_pin_en(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON2),
				       (kal_uint8) (val),
				       (kal_uint8) (CON2_IINSET_PIN_EN_MASK),
				       (kal_uint8) (CON2_IINSET_PIN_EN_SHIFT)
	    );
}

void ncp1854_set_iinlim_en(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON2),
				       (kal_uint8) (val),
				       (kal_uint8) (CON2_IINLIM_EN_MASK),
				       (kal_uint8) (CON2_IINLIM_EN_SHIFT)
	    );
}

void ncp1854_set_aicl_en(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON2),
				       (kal_uint8) (val),
				       (kal_uint8) (CON2_AICL_EN_MASK),
				       (kal_uint8) (CON2_AICL_EN_SHIFT)
	    );
}

/* CON8 */
kal_uint32 ncp1854_get_vfet_ok(void)
{
	kal_uint32 ret = 0;
	kal_uint8 val = 0;

	ret = ncp1854_read_interface((kal_uint8) (NCP1854_CON8),
				     (&val),
				     (kal_uint8) (CON8_VFET_OK_MASK),
				     (kal_uint8) (CON8_VFET_OK_SHIFT)
	    );
	return val;
}


/* CON14 */
void ncp1854_set_ctrl_vbat(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON14),
				       (kal_uint8) (val),
				       (kal_uint8) (CON14_CTRL_VBAT_MASK),
				       (kal_uint8) (CON14_CTRL_VBAT_SHIFT)
	    );
}

/* CON15 */
void ncp1854_set_ichg_high(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON15),
				       (kal_uint8) (val),
				       (kal_uint8) (CON15_ICHG_HIGH_MASK),
				       (kal_uint8) (CON15_ICHG_HIGH_SHIFT)
	    );
}

void ncp1854_set_ieoc(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON15),
				       (kal_uint8) (val),
				       (kal_uint8) (CON15_IEOC_MASK), (kal_uint8) (CON15_IEOC_SHIFT)
	    );
}

void ncp1854_set_ichg(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON15),
				       (kal_uint8) (val),
				       (kal_uint8) (CON15_ICHG_MASK), (kal_uint8) (CON15_ICHG_SHIFT)
	    );
}

kal_uint32 ncp1854_get_ichg(void)
{
	kal_uint32 ret = 0;
	kal_uint8 val = 0;

	ret = ncp1854_read_interface((kal_uint8) NCP1854_CON15,
				     (&val),
				     (kal_uint8) CON15_ICHG_MASK, (kal_uint8) CON15_ICHG_SHIFT);
	return val;
}

/* CON16 */
void ncp1854_set_iweak(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON16),
				       (kal_uint8) (val),
				       (kal_uint8) (CON16_IWEAK_MASK),
				       (kal_uint8) (CON16_IWEAK_SHIFT)
	    );
}

void ncp1854_set_ctrl_vfet(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON16),
				       (kal_uint8) (val),
				       (kal_uint8) (CON16_CTRL_VFET_MASK),
				       (kal_uint8) (CON16_CTRL_VFET_SHIFT)
	    );
}

void ncp1854_set_iinlim(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON16),
				       (kal_uint8) (val),
				       (kal_uint8) (CON16_IINLIM_MASK),
				       (kal_uint8) (CON16_IINLIM_SHIFT)
	    );
}

/* CON17 */

void ncp1854_set_iinlim_ta(kal_uint32 val)
{
	kal_uint32 ret = 0;

	ret = ncp1854_config_interface((kal_uint8) (NCP1854_CON17),
				       (kal_uint8) (val),
				       (kal_uint8) (CON17_IINLIM_TA_MASK),
				       (kal_uint8) (CON17_IINLIM_TA_SHIFT)
	    );
}


/**********************************************************
  *
  *   [Internal Function]
  *
  *********************************************************/
void ncp1854_dump_register(void)
{
	int i = 0;

	for (i = 0; i < NCP1854_REG_NUM; i++) {
		if ((i == 3) || (i == 4) || (i == 5) || (i == 6))	/* do not dump read clear status register */
			continue;
		if ((i == 10) || (i == 11) || (i == 12) || (i == 13))	/* do not dump interrupt mask bit register */
			continue;
		ncp1854_read_byte(i, &ncp1854_reg[i]);
		printf("[ncp1854_dump_register] Reg[0x%X]=0x%X\n", i, ncp1854_reg[i]);
	}

}

void ncp1854_hw_init(void)
{
	printf("[ncp1854] ChargerHwInit_ncp1854\n");

	kal_uint32 ncp1854_status;

	ncp1854_status = ncp1854_get_chip_status();
	/* if you want disable factory mode,the FTRY pin and FCTRY_MOD_REG need different */
#ifdef DISABLE_NCP1854_FACTORY_MODE
	ncp1854_set_fctry_mode(0x0);
#else
	ncp1854_set_fctry_mode(0x1);
#endif
	ncp1854_set_otg_en(0x0);
	ncp1854_set_trans_en(0);
	ncp1854_set_tj_warn_opt(0x0);
/* ncp1854_set_int_mask(0x0); //disable all interrupt */
	ncp1854_set_int_mask(0x1);	/* enable all interrupt for boost mode status monitor */
/* ncp1854_set_tchg_rst(0x1); //reset charge timer */
#ifdef NCP1854_PWR_PATH
	ncp1854_set_pwr_path(0x1);
#else
	ncp1854_set_pwr_path(0x0);
#endif
	if ((ncp1854_status == 0x8) || (ncp1854_status == 0x9) || (ncp1854_status == 0xA))	/* WEAK WAIT, WEAK SAFE, WEAK CHARGE */
		ncp1854_set_ctrl_vbat(0x1C);	/* VCHG = 4.0V */
	else {
		ncp1854_set_ctrl_vbat(0x24);	/* VCHG = 4.2V */

		ncp1854_set_aicl_en(0x1);	/* enable AICL as PT team suggest */

		ncp1854_set_iinset_pin_en(0x0);	/* Input current limit and AICL control by I2C */
		ncp1854_set_chgto_dis(0x1);	/* disable charge timer */
	}
	ncp1854_set_ieoc(0x4);	/* terminate current = 200mA for ICS optimized suspend power */

	ncp1854_set_iweak(0x3);	/* weak charge current = 300mA */

	ncp1854_set_ctrl_vfet(0x0);	/* VFET = 3.1V */
}


static CHARGER_TYPE g_chr_type_num = CHARGER_UNKNOWN;
int hw_charging_get_charger_type(void);
extern int g_std_ac_large_current_en;

void ncp1854_charging_enable(kal_uint32 bEnable)
{
	int temp_CC_value = 0;
	kal_int32 bat_val = 0;

	if (CHARGER_UNKNOWN == g_chr_type_num && KAL_TRUE == upmu_is_chr_det()) {
		hw_charging_get_charger_type();
		dprintf(CRITICAL, "[BATTERY:ncp1854] charger type: %d\n", g_chr_type_num);
	}

	bat_val = get_i_sense_volt(1);
	if (g_chr_type_num == STANDARD_CHARGER) {

		if (g_std_ac_large_current_en == 1) {
			temp_CC_value = 2000;
			ncp1854_set_iinlim_ta(0xF);	/* IN current limit at 2A */
			ncp1854_set_iinlim_en(0x1);	/* IN current limit enable */

			if (bat_val < PRECC_BATVOL) {
				ncp1854_set_ichg_high(0x0);	/* ICHG */
				ncp1854_set_ichg(0x1);	/* Pre-Charging Current Limit at 500mA */
			} else {
				ncp1854_set_ichg_high(0);	/* ICHG */
				ncp1854_set_ichg(0xF);	/* Fast Charging Current Limit at 1.9A */
			}

		} else {
			temp_CC_value = 1500;
			ncp1854_set_iinlim_ta(0xA);	/* IN current limit at 1.5A */
			ncp1854_set_iinlim_en(0x1);	/* IN current limit enable */

			if (bat_val < PRECC_BATVOL) {
				ncp1854_set_ichg_high(0x0);	/* ICHG */
				ncp1854_set_ichg(0x1);	/* Pre-Charging Current Limit at 500mA */
			} else {
				ncp1854_set_ichg_high(0);	/* ICHG */
				ncp1854_set_ichg(0xB);	/* Fast Charging Current Limit at 1.5A */
			}
		}

	} else if (g_chr_type_num == STANDARD_HOST
		   || g_chr_type_num == CHARGING_HOST || g_chr_type_num == NONSTANDARD_CHARGER) {
		temp_CC_value = 500;
		ncp1854_set_iinlim_ta(0);	/* IINLIM */
		ncp1854_set_iinlim(0x1);	/* IN current limit at 500mA */
		ncp1854_set_iinlim_en(0x1);	/* IN current limit enable */

		ncp1854_set_ichg_high(0x0);	/* ICHG */
		ncp1854_set_ichg(0x1);	/* Pre-Charging Current Limit at 500mA */

	} else {
		temp_CC_value = 500;
		ncp1854_set_iinlim_ta(0);	/* IINLIM */
		ncp1854_set_iinlim(0x1);	/* IN current limit at 500mA */
		ncp1854_set_iinlim_en(0x1);	/* IN current limit enable */

		ncp1854_set_ichg_high(0x0);	/* ICHG */
		ncp1854_set_ichg(0x1);	/* Pre-Charging Current Limit at 500mA */

	}

	if (KAL_TRUE == bEnable)
		ncp1854_set_chg_en(0x1);	/* charger enable */
	else
		ncp1854_set_chg_en(0x0);	/* charger disable */

	ncp1854_set_wdto_dis(0x0);
	dprintf(INFO, "[BATTERY:ncp1854] ncp1854_set_ac_current(), CC value(%dmA) \r\n",
		temp_CC_value);
	dprintf(INFO, "[BATTERY:ncp1854] charger enable/disable %d !\r\n", bEnable);
}


#if defined(CONFIG_POWER_EXT)

int hw_charging_get_charger_type(void)
{
	g_chr_type_num = STANDARD_HOST;

	return STANDARD_HOST;
}

#else

extern void Charger_Detect_Init(void);
extern void Charger_Detect_Release(void);
extern void mdelay(unsigned long msec);
extern kal_uint16 bc11_set_register_value(PMU_FLAGS_LIST_ENUM flagname, kal_uint32 val);

static void hw_bc11_dump_register(void)
{
/*
	kal_uint32 reg_val = 0;
	kal_uint32 reg_num = CHR_CON18;
	kal_uint32 i = 0;

	for(i=reg_num ; i<=CHR_CON19 ; i+=2)
	{
		reg_val = upmu_get_reg_value(i);
		dprintf(INFO, "Chr Reg[0x%x]=0x%x \r\n", i, reg_val);
	}
*/
}

static void hw_bc11_init(void)
{
	mdelay(200);
	Charger_Detect_Init();

	/* RG_bc11_BIAS_EN=1 */
	bc11_set_register_value(PMIC_RG_BC11_BIAS_EN, 1);
	/* RG_bc11_VSRC_EN[1:0]=00 */
	bc11_set_register_value(PMIC_RG_BC11_VSRC_EN, 0);
	/* RG_bc11_VREF_VTH = [1:0]=00 */
	bc11_set_register_value(PMIC_RG_BC11_VREF_VTH, 0);
	/* RG_bc11_CMP_EN[1.0] = 00 */
	bc11_set_register_value(PMIC_RG_BC11_CMP_EN, 0);
	/* RG_bc11_IPU_EN[1.0] = 00 */
	bc11_set_register_value(PMIC_RG_BC11_IPU_EN, 0);
	/* RG_bc11_IPD_EN[1.0] = 00 */
	bc11_set_register_value(PMIC_RG_BC11_IPD_EN, 0);
	/* bc11_RST=1 */
	bc11_set_register_value(PMIC_RG_BC11_RST, 1);
	/* bc11_BB_CTRL=1 */
	bc11_set_register_value(PMIC_RG_BC11_BB_CTRL, 1);

	mdelay(50);

	if (g_ncp1854_log_en > 1) {
		dprintf(INFO, "hw_bc11_init() \r\n");
		hw_bc11_dump_register();
	}
}

static U32 hw_bc11_DCD(void)
{
	U32 wChargerAvail = 0;

	/* RG_bc11_IPU_EN[1.0] = 10 */
	bc11_set_register_value(PMIC_RG_BC11_IPU_EN, 0x2);
	/* RG_bc11_IPD_EN[1.0] = 01 */
	bc11_set_register_value(PMIC_RG_BC11_IPD_EN, 0x1);
	/* RG_bc11_VREF_VTH = [1:0]=01 */
	bc11_set_register_value(PMIC_RG_BC11_VREF_VTH, 0x1);
	/* RG_bc11_CMP_EN[1.0] = 10 */
	bc11_set_register_value(PMIC_RG_BC11_CMP_EN, 0x2);

	mdelay(80);

	wChargerAvail = bc11_get_register_value(PMIC_RGS_BC11_CMP_OUT);

	if (g_ncp1854_log_en > 1) {
		dprintf(INFO, "hw_bc11_DCD() \r\n");
		hw_bc11_dump_register();
	}
	/* RG_bc11_IPU_EN[1.0] = 00 */
	bc11_set_register_value(PMIC_RG_BC11_IPU_EN, 0x0);
	/* RG_bc11_IPD_EN[1.0] = 00 */
	bc11_set_register_value(PMIC_RG_BC11_IPD_EN, 0x0);
	/* RG_bc11_CMP_EN[1.0] = 00 */
	bc11_set_register_value(PMIC_RG_BC11_CMP_EN, 0x0);
	/* RG_bc11_VREF_VTH = [1:0]=00 */
	bc11_set_register_value(PMIC_RG_BC11_VREF_VTH, 0x0);

	return wChargerAvail;
}

static U32 hw_bc11_stepA1(void)
{
	U32 wChargerAvail = 0;

	/* RG_bc11_IPD_EN[1.0] = 01 */
	bc11_set_register_value(PMIC_RG_BC11_IPD_EN, 0x1);
	/* RG_bc11_VREF_VTH = [1:0]=00 */
	bc11_set_register_value(PMIC_RG_BC11_VREF_VTH, 0x0);
	/* RG_bc11_CMP_EN[1.0] = 01 */
	bc11_set_register_value(PMIC_RG_BC11_CMP_EN, 0x1);

	mdelay(80);

	wChargerAvail = bc11_get_register_value(PMIC_RGS_BC11_CMP_OUT);

	if (g_ncp1854_log_en > 1) {
		dprintf(INFO, "hw_bc11_stepA1() \r\n");
		hw_bc11_dump_register();
	}
	/* RG_bc11_IPD_EN[1.0] = 00 */
	bc11_set_register_value(PMIC_RG_BC11_IPD_EN, 0x0);
	/* RG_bc11_CMP_EN[1.0] = 00 */
	bc11_set_register_value(PMIC_RG_BC11_CMP_EN, 0x0);

	return wChargerAvail;
}


static U32 hw_bc11_stepA2(void)
{
	U32 wChargerAvail = 0;

	/* RG_bc11_VSRC_EN[1.0] = 10 */
	bc11_set_register_value(PMIC_RG_BC11_VSRC_EN, 0x2);
	/* RG_bc11_IPD_EN[1:0] = 01 */
	bc11_set_register_value(PMIC_RG_BC11_IPD_EN, 0x1);
	/* RG_bc11_VREF_VTH = [1:0]=00 */
	bc11_set_register_value(PMIC_RG_BC11_VREF_VTH, 0x0);
	/* RG_bc11_CMP_EN[1.0] = 01 */
	bc11_set_register_value(PMIC_RG_BC11_CMP_EN, 0x1);

	mdelay(80);

	wChargerAvail = bc11_get_register_value(PMIC_RGS_BC11_CMP_OUT);

	if (g_ncp1854_log_en) {
		dprintf(INFO, "hw_bc11_stepB1() \r\n");
		hw_bc11_dump_register();
	}
	/* RG_bc11_VSRC_EN[1:0]=00 */
	bc11_set_register_value(PMIC_RG_BC11_VSRC_EN, 0x0);
	/* RG_bc11_IPD_EN[1.0] = 00 */
	bc11_set_register_value(PMIC_RG_BC11_IPD_EN, 0x0);
	/* RG_bc11_CMP_EN[1.0] = 00 */
	bc11_set_register_value(PMIC_RG_BC11_CMP_EN, 0x0);

	return wChargerAvail;
}


static U32 hw_bc11_stepB2(void)
{
	U32 wChargerAvail = 0;

	/* RG_bc11_IPU_EN[1:0]=10 */
	bc11_set_register_value(PMIC_RG_BC11_IPU_EN, 0x2);
	/* RG_bc11_VREF_VTH = [1:0]=01 */
	bc11_set_register_value(PMIC_RG_BC11_VREF_VTH, 0x1);
	/* RG_bc11_CMP_EN[1.0] = 01 */
	bc11_set_register_value(PMIC_RG_BC11_CMP_EN, 0x1);

	mdelay(80);

	wChargerAvail = bc11_get_register_value(PMIC_RGS_BC11_CMP_OUT);

	if (g_ncp1854_log_en) {
		dprintf(INFO, "hw_bc11_stepB2() \r\n");
		hw_bc11_dump_register();
	}

	if (!wChargerAvail) {
		/* RG_bc11_VSRC_EN[1.0] = 10 */
		/* mt6325_upmu_set_rg_bc11_vsrc_en(0x2); */
		bc11_set_register_value(PMIC_RG_BC11_VSRC_EN, 0x2);
	}
	/* RG_bc11_IPU_EN[1.0] = 00 */
	bc11_set_register_value(PMIC_RG_BC11_IPU_EN, 0x0);
	/* RG_bc11_CMP_EN[1.0] = 00 */
	bc11_set_register_value(PMIC_RG_BC11_CMP_EN, 0x0);
	/* RG_bc11_VREF_VTH = [1:0]=00 */
	bc11_set_register_value(PMIC_RG_BC11_VREF_VTH, 0x0);

	return wChargerAvail;
}


static void hw_bc11_done(void)
{
	/* RG_bc11_VSRC_EN[1:0]=00 */
	bc11_set_register_value(PMIC_RG_BC11_VSRC_EN, 0x0);
	/* RG_bc11_VREF_VTH = [1:0]=0 */
	bc11_set_register_value(PMIC_RG_BC11_VREF_VTH, 0x0);
	/* RG_bc11_CMP_EN[1.0] = 00 */
	bc11_set_register_value(PMIC_RG_BC11_CMP_EN, 0x0);
	/* RG_bc11_IPU_EN[1.0] = 00 */
	bc11_set_register_value(PMIC_RG_BC11_IPU_EN, 0x0);
	/* RG_bc11_IPD_EN[1.0] = 00 */
	bc11_set_register_value(PMIC_RG_BC11_IPD_EN, 0x0);
	/* RG_bc11_BIAS_EN=0 */
	bc11_set_register_value(PMIC_RG_BC11_BIAS_EN, 0x0);

	Charger_Detect_Release();

	if (g_ncp1854_log_en > 1) {
		dprintf(INFO, "hw_bc11_done() \r\n");
		hw_bc11_dump_register();
	}
}

int hw_charging_get_charger_type(void)
{
	if (CHARGER_UNKNOWN != g_chr_type_num)
		return g_chr_type_num;
#if 0
	return STANDARD_HOST;
#else
	CHARGER_TYPE CHR_Type_num = CHARGER_UNKNOWN;

    /********* Step initial  ***************/
	hw_bc11_init();

    /********* Step DCD ***************/
	if (1 == hw_bc11_DCD()) {
	 /********* Step A1 ***************/
		if (1 == hw_bc11_stepA1()) {
			CHR_Type_num = APPLE_2_1A_CHARGER;
			dprintf(INFO, "step A1 : Apple 2.1A CHARGER!\r\n");
		} else {
			CHR_Type_num = NONSTANDARD_CHARGER;
			dprintf(INFO, "step A1 : Non STANDARD CHARGER!\r\n");
		}
	} else {
	 /********* Step A2 ***************/
		if (1 == hw_bc11_stepA2()) {
	     /********* Step B2 ***************/
			if (1 == hw_bc11_stepB2()) {
				CHR_Type_num = STANDARD_CHARGER;
				dprintf(INFO, "step B2 : STANDARD CHARGER!\r\n");
			} else {
				CHR_Type_num = CHARGING_HOST;
				dprintf(INFO, "step B2 :  Charging Host!\r\n");
			}
		} else {
			CHR_Type_num = STANDARD_HOST;
			dprintf(INFO, "step A2 : Standard USB Host!\r\n");
		}
	}

    /********* Finally setting *******************************/
	hw_bc11_done();

	g_chr_type_num = CHR_Type_num;

	return g_chr_type_num;
#endif
}
#endif