mtk-lk/dev/lcm/CPT_CLAA101FP01_DSI_VDO/CPT_CLAA101FP01_DSI_VDO.c

/* Copyright Statement:
*
* This software/firmware and related documentation ("MediaTek Software") are
* protected under relevant copyright laws. The information contained herein
* is confidential and proprietary to MediaTek Inc. and/or its licensors.
* Without the prior written permission of MediaTek inc. and/or its licensors,
* any reproduction, modification, use or disclosure of MediaTek Software,
* and information contained herein, in whole or in part, shall be strictly prohibited.
*/
/* MediaTek Inc. (C) 2015. All rights reserved.
*
* BY OPENING THIS FILE, RECEIVER HEREBY UNEQUIVOCALLY ACKNOWLEDGES AND AGREES
* THAT THE SOFTWARE/FIRMWARE AND ITS DOCUMENTATIONS ("MEDIATEK SOFTWARE")
* RECEIVED FROM MEDIATEK AND/OR ITS REPRESENTATIVES ARE PROVIDED TO RECEIVER ON
* AN "AS-IS" BASIS ONLY. MEDIATEK EXPRESSLY DISCLAIMS ANY AND ALL WARRANTIES,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT.
* NEITHER DOES MEDIATEK PROVIDE ANY WARRANTY WHATSOEVER WITH RESPECT TO THE
* SOFTWARE OF ANY THIRD PARTY WHICH MAY BE USED BY, INCORPORATED IN, OR
* SUPPLIED WITH THE MEDIATEK SOFTWARE, AND RECEIVER AGREES TO LOOK ONLY TO SUCH
* THIRD PARTY FOR ANY WARRANTY CLAIM RELATING THERETO. RECEIVER EXPRESSLY ACKNOWLEDGES
* THAT IT IS RECEIVER'S SOLE RESPONSIBILITY TO OBTAIN FROM ANY THIRD PARTY ALL PROPER LICENSES
* CONTAINED IN MEDIATEK SOFTWARE. MEDIATEK SHALL ALSO NOT BE RESPONSIBLE FOR ANY MEDIATEK
* SOFTWARE RELEASES MADE TO RECEIVER'S SPECIFICATION OR TO CONFORM TO A PARTICULAR
* STANDARD OR OPEN FORUM. RECEIVER'S SOLE AND EXCLUSIVE REMEDY AND MEDIATEK'S ENTIRE AND
* CUMULATIVE LIABILITY WITH RESPECT TO THE MEDIATEK SOFTWARE RELEASED HEREUNDER WILL BE,
* AT MEDIATEK'S OPTION, TO REVISE OR REPLACE THE MEDIATEK SOFTWARE AT ISSUE,
* OR REFUND ANY SOFTWARE LICENSE FEES OR SERVICE CHARGE PAID BY RECEIVER TO
* MEDIATEK FOR SUCH MEDIATEK SOFTWARE AT ISSUE.
*
* The following software/firmware and/or related documentation ("MediaTek Software")
* have been modified by MediaTek Inc. All revisions are subject to any receiver\'s
* applicable license agreements with MediaTek Inc.
*/
#ifndef BUILD_LK
#include <linux/string.h>
#else
#include <string.h>
#endif
#include "lcm_drv.h"

#ifdef BUILD_LK
	#include <platform/mt_gpio.h>
	#include <platform/mt_pmic.h>
#elif defined(BUILD_UBOOT)
#else
	#include <mach/mt_gpio.h>
	#include <mach/mt_pm_ldo.h>
#endif

// ---------------------------------------------------------------------------
//  Local Constants
// ---------------------------------------------------------------------------

#define FRAME_WIDTH  (1920) //(800)
#define FRAME_HEIGHT (1200) //(1280)

#define LCM_ID_NT35590 (0x90)
// TODO. This LCM ID is NT51012 not 35590.

#define GPIO_LCD_RST_EN      GPIO65
#define GPIO_LCD_STB_EN      GPIO66
#define GPIO_LCD_LED_EN      GPIO_LCM_LED_EN //GPIO76

#define GPIO_LCD_LED_PWM_EN      (GPIO116 | 0x80000000) //GPIO116


// ---------------------------------------------------------------------------
//  Local Variables
// ---------------------------------------------------------------------------

//static LCM_UTIL_FUNCS lcm_util = {0};  //for fixed warning issue
static LCM_UTIL_FUNCS lcm_util = 
{
	.set_reset_pin = NULL,
	.udelay = NULL,
	.mdelay = NULL,
};


#define SET_RESET_PIN(v)    (lcm_util.set_reset_pin((v)))

#define UDELAY(n) (lcm_util.udelay(n))
#define MDELAY(n) (lcm_util.mdelay(n))


// ---------------------------------------------------------------------------
//  Local Functions
// ---------------------------------------------------------------------------

#define dsi_set_cmdq_V2(cmd, count, ppara, force_update)	        lcm_util.dsi_set_cmdq_V2(cmd, count, ppara, force_update)
#define dsi_set_cmdq(pdata, queue_size, force_update)		lcm_util.dsi_set_cmdq(pdata, queue_size, force_update)
#define wrtie_cmd(cmd)										lcm_util.dsi_write_cmd(cmd)
#define write_regs(addr, pdata, byte_nums)					lcm_util.dsi_write_regs(addr, pdata, byte_nums)
#define read_reg(cmd)											lcm_util.dsi_dcs_read_lcm_reg(cmd)
#define read_reg_v2(cmd, buffer, buffer_size)   				lcm_util.dsi_dcs_read_lcm_reg_v2(cmd, buffer, buffer_size)   


#define   LCM_DSI_CMD_MODE							0

#if 0
static void init_lcm_registers(void)
{
	unsigned int data_array[16];
		
#if 1

	data_array[0] = 0x00011500;  //software reset					 
	dsi_set_cmdq(data_array, 1, 1);
	
	MDELAY(20);
	
	data_array[0]=0x0bae1500;
	data_array[1]=0xeaee1500;
	data_array[2]=0x5fef1500;
	data_array[3]=0x68f21500;	
	data_array[4]=0x00ee1500;
	data_array[5]=0x00ef1500;
	dsi_set_cmdq(&data_array, 6, 1);

#if 0

	data_array[0] = 0x7DB21500;  					 
	dsi_set_cmdq(data_array, 1, 1);

	data_array[0] = 0x0BAE1500;  					 
	dsi_set_cmdq(data_array, 1, 1);
	
	data_array[0] = 0x18B61500;  					 
	dsi_set_cmdq(data_array, 1, 1);
	
	data_array[0] = 0xEAEE1500;  					 
	dsi_set_cmdq(data_array, 1, 1);
	
	data_array[0] = 0x5FEF1500;  					 
	dsi_set_cmdq(data_array, 1, 1);
	
	data_array[0] = 0x68F21500;  					 
	dsi_set_cmdq(data_array, 1, 1);
	
	data_array[0] = 0x00EE1500;  					 
	dsi_set_cmdq(data_array, 1, 1);

	data_array[0] = 0x00EF1500;  					 
	dsi_set_cmdq(data_array, 1, 1);
	
	data_array[0] = 0x64D21500;  					 
	dsi_set_cmdq(data_array, 1, 1);

	data_array[0] = 0x00101500;  //sleep out                        
	dsi_set_cmdq(data_array, 1, 1);
	MDELAY(20);
#endif

	//data_array[0] = 0xEFB11500;                       
	//dsi_set_cmdq(data_array, 1, 1);
	//MDELAY(1);

	//data_array[0] = 0x00290500;  //display on                        
	//dsi_set_cmdq(data_array, 1, 1);
#endif

#if 0
	data_array[0] = 0x00010500;  //software reset					 
	dsi_set_cmdq(data_array, 1, 1);
	
	MDELAY(20);

	data_array[0] = 0x00023902; 
	data_array[1] = 0x00000BAE; 					 
	dsi_set_cmdq(data_array, 2, 1);
	MDELAY(1);
	
	data_array[0] = 0x00023902; 
	data_array[1] = 0x0000EAEE; 					 
	dsi_set_cmdq(data_array, 2, 1);
	MDELAY(1);
	
	data_array[0] = 0x00023902; 
	data_array[1] = 0x00005FEF; 					 
	dsi_set_cmdq(data_array, 2, 1);
	MDELAY(1);
	
	data_array[0] = 0x00023902; 
	data_array[1] = 0x000068F2; 					 
	dsi_set_cmdq(data_array, 2, 1);
	MDELAY(1);
	
	data_array[0] = 0x00023902; 
	data_array[1] = 0x000000EE; 					 
	dsi_set_cmdq(data_array, 2, 1);
	MDELAY(1);
	
	data_array[0] = 0x00023902; 
	data_array[1] = 0x000000EF; 					 
	dsi_set_cmdq(data_array, 2, 1);
	MDELAY(1);
	
	data_array[0] = 0x00100500;  //sleep out                        
	dsi_set_cmdq(data_array, 1, 1);
	MDELAY(20);

	data_array[0] = 0x00290500;  //display on                        
	dsi_set_cmdq(data_array, 1, 1);
#endif
	//MDELAY(5);
}
#endif

// ---------------------------------------------------------------------------
//  LCM Driver Implementations
// ---------------------------------------------------------------------------

static void lcm_set_util_funcs(const LCM_UTIL_FUNCS *util)
{
    memcpy(&lcm_util, util, sizeof(LCM_UTIL_FUNCS));
}


static void lcm_get_params(LCM_PARAMS *params)
{

		memset(params, 0, sizeof(LCM_PARAMS));
	
		params->type   = LCM_TYPE_DSI;

		params->width  = FRAME_WIDTH;
		params->height = FRAME_HEIGHT;

#if 0
		// enable tearing-free
		params->dbi.te_mode 				= LCM_DBI_TE_MODE_VSYNC_ONLY;
		params->dbi.te_edge_polarity		= LCM_POLARITY_RISING;
#endif

        #if (LCM_DSI_CMD_MODE)
		params->dsi.mode   = CMD_MODE;
        #else
		params->dsi.mode   = SYNC_EVENT_VDO_MODE; //SYNC_PULSE_VDO_MODE; //BURST_VDO_MODE; //;
        #endif
	
		// DSI
		/* Command mode setting */
		//1 Three lane or Four lane
		params->dsi.LANE_NUM				= LCM_FOUR_LANE;
		//The following defined the fomat for data coming from LCD engine.
		params->dsi.data_format.color_order = LCM_COLOR_ORDER_RGB;
		params->dsi.data_format.trans_seq   = LCM_DSI_TRANS_SEQ_MSB_FIRST;
		params->dsi.data_format.padding     = LCM_DSI_PADDING_ON_LSB;
		params->dsi.data_format.format      = LCM_DSI_FORMAT_RGB888;

		// Highly depends on LCD driver capability.
		// Not support in MT6573
		params->dsi.packet_size=256;

		// Video mode setting		
		params->dsi.intermediat_buffer_num = 0;//because DSI/DPI HW design change, this parameters should be 0 when video mode in MT658X; or memory leakage

		params->dsi.PS=LCM_PACKED_PS_24BIT_RGB888;
		params->dsi.word_count=1920*3; //720*3;	

		
		params->dsi.vertical_sync_active				= 4; //4; //6; //(12-4-4); //1;
		params->dsi.vertical_backporch					= 20; //4; //6; //4; //6; //10;
		params->dsi.vertical_frontporch					= 15; //4;//6; //4//6; //10;
		params->dsi.vertical_active_line				= FRAME_HEIGHT; 

		params->dsi.horizontal_sync_active				= 40; //40; //44; //(120-40-40); //1;
		params->dsi.horizontal_backporch				= 80; //40;//44; //40; //44; //57;
		params->dsi.horizontal_frontporch				= 80; //40;//44; //40; //44; //32;
		params->dsi.horizontal_active_pixel				= FRAME_WIDTH;

		// Bit rate calculation
		//1 Every lane speed
		//params->dsi.pll_div1=1; //0;		// div1=0,1,2,3;div1_real=1,2,4,4 ----0: 546Mbps  1:273Mbps
		//params->dsi.pll_div2=1;		// div2=0,1,2,3;div1_real=1,2,4,4	
		//params->dsi.fbk_div =22;//31;    // fref=26MHz, fvco=fref*(fbk_div+1)*2/(div1_real*div2_real)	
		//params->dsi.fbk_sel =0;
		//params->dsi.fbk_div =45;
        params->dsi.PLL_CLOCK = LCM_DSI_6589_PLL_CLOCK_481;//LCM_DSI_6589_PLL_CLOCK_NULL; //LCM_DSI_6589_PLL_CLOCK_396_5;
    
		//params->dsi.CLK_ZERO = 262; //47;
		//params->dsi.HS_ZERO = 117; //36;

		//params->dsi.cont_clock = 1;
		//params->dsi.noncont_clock = TRUE; 
		//params->dsi.noncont_clock_period = 2; // Unit : frames

}
//extern void DSI_clk_HS_mode(unsigned char enter);
static void lcm_init(void)
{
	//unsigned int data_array[16];
#ifdef BUILD_LK
		printf("[LK/LCM] lcm_init() enter\n");
	//VGP6 3.3V
	pmic_config_interface(0x424, 0x1, 0x1, 15); 
	pmic_config_interface(0x45a, 0x07, 0x07, 5);
	
	//mt_set_gpio_mode(GPIO_LCD_RST_EN, GPIO_MODE_00);
	//mt_set_gpio_dir(GPIO_LCD_RST_EN, GPIO_DIR_OUT);
	//mt_set_gpio_out(GPIO_LCD_RST_EN, GPIO_OUT_ONE);
	#if 0
	mt_set_gpio_mode(GPIO_LCD_LED_PWM_EN, GPIO_MODE_00);
	mt_set_gpio_dir(GPIO_LCD_LED_PWM_EN, GPIO_DIR_OUT);
	mt_set_gpio_out(GPIO_LCD_LED_PWM_EN, GPIO_OUT_ONE);
	#endif
	MDELAY(20);
	
	//mt_set_gpio_mode(GPIO_LCD_STB_EN, GPIO_MODE_00);
	//mt_set_gpio_dir(GPIO_LCD_STB_EN, GPIO_DIR_OUT);
	//mt_set_gpio_out(GPIO_LCD_STB_EN, GPIO_OUT_ONE);
	mt_set_gpio_mode(GPIO_LCD_LED_EN, GPIO_MODE_00);
	mt_set_gpio_dir(GPIO_LCD_LED_EN, GPIO_DIR_OUT);
	mt_set_gpio_out(GPIO_LCD_LED_EN, GPIO_OUT_ONE);
	MDELAY(20);
#endif

	MDELAY(50); 
	
	SET_RESET_PIN(1);
	SET_RESET_PIN(0);
	MDELAY(1);
	SET_RESET_PIN(1);


	MDELAY(150);
    
	MDELAY(10);
	//DSI_clk_HS_mode(1);
	  MDELAY(180);
	MDELAY(220);
	//init_lcm_registers();
	//data_array[0] = 0x55142300;  //turn on bist mode					 
	//dsi_set_cmdq(data_array, 1, 1);
	
	MDELAY(150);
}



static void lcm_suspend(void)
{
	//unsigned int data_array[16];

	//data_array[0]=0x00280500; // Display Off
	//dsi_set_cmdq(data_array, 1, 1);
	#if 0
	mt_set_gpio_mode(GPIO_LCD_LED_PWM_EN, GPIO_MODE_00);
	mt_set_gpio_dir(GPIO_LCD_LED_PWM_EN, GPIO_DIR_OUT);
	mt_set_gpio_out(GPIO_LCD_LED_PWM_EN, GPIO_OUT_ZERO);
	#endif
	MDELAY(20);
	//
	mt_set_gpio_mode(GPIO_LCD_LED_EN, GPIO_MODE_00);
	mt_set_gpio_dir(GPIO_LCD_LED_EN, GPIO_DIR_OUT);
	mt_set_gpio_out(GPIO_LCD_LED_EN, GPIO_OUT_ZERO);
	MDELAY(20);
	
	//data_array[0] = 0x00111500; // Sleep In
	//dsi_set_cmdq(data_array, 1, 1);

	MDELAY(160);

	MDELAY(10);
	//DSI_clk_HS_mode(0);
	  MDELAY(80);
	//SET_RESET_PIN(0);
}


static void lcm_resume(void)
{
#ifdef BUILD_LK
	printf("[LK/LCM] lcm_resume() enter\n");
	//VGP6 3.3V
	pmic_config_interface(0x424, 0x1, 0x1, 15); 
	pmic_config_interface(0x45a, 0x07, 0x07, 5);
		
	//mt_set_gpio_mode(GPIO_LCD_RST_EN, GPIO_MODE_00);
	//mt_set_gpio_dir(GPIO_LCD_RST_EN, GPIO_DIR_OUT);
	//mt_set_gpio_out(GPIO_LCD_RST_EN, GPIO_OUT_ONE);
	#if 0
	mt_set_gpio_mode(GPIO_LCD_LED_PWM_EN, GPIO_MODE_00);
	mt_set_gpio_dir(GPIO_LCD_LED_PWM_EN, GPIO_DIR_OUT);
	mt_set_gpio_out(GPIO_LCD_LED_PWM_EN, GPIO_OUT_ONE);
	#endif
	MDELAY(20);
	MDELAY(20);
		
	//mt_set_gpio_mode(GPIO_LCD_STB_EN, GPIO_MODE_00);
	//mt_set_gpio_dir(GPIO_LCD_STB_EN, GPIO_DIR_OUT);
	//mt_set_gpio_out(GPIO_LCD_STB_EN, GPIO_OUT_ONE);
	mt_set_gpio_mode(GPIO_LCD_LED_EN, GPIO_MODE_00);
	mt_set_gpio_dir(GPIO_LCD_LED_EN, GPIO_DIR_OUT);
	mt_set_gpio_out(GPIO_LCD_LED_EN, GPIO_OUT_ONE);
	MDELAY(20);
#endif

	//unsigned int data_array[16];
	lcm_init();

	//data_array[0] = 0x00101500; // Sleep Out
	//dsi_set_cmdq(data_array, 1, 1);
	MDELAY(150);

	//data_array[0] = 0x00290500; // Display On
	//dsi_set_cmdq(data_array, 1, 1);

}
         
#if (LCM_DSI_CMD_MODE)
static void lcm_update(unsigned int x, unsigned int y,
                       unsigned int width, unsigned int height)
{
	unsigned int x0 = x;
	unsigned int y0 = y;
	unsigned int x1 = x0 + width - 1;
	unsigned int y1 = y0 + height - 1;

	unsigned char x0_MSB = ((x0>>8)&0xFF);
	unsigned char x0_LSB = (x0&0xFF);
	unsigned char x1_MSB = ((x1>>8)&0xFF);
	unsigned char x1_LSB = (x1&0xFF);
	unsigned char y0_MSB = ((y0>>8)&0xFF);
	unsigned char y0_LSB = (y0&0xFF);
	unsigned char y1_MSB = ((y1>>8)&0xFF);
	unsigned char y1_LSB = (y1&0xFF);

	unsigned int data_array[16];

	data_array[0]= 0x00053902;
	data_array[1]= (x1_MSB<<24)|(x0_LSB<<16)|(x0_MSB<<8)|0x2a;
	data_array[2]= (x1_LSB);
	dsi_set_cmdq(data_array, 3, 1);
	
	data_array[0]= 0x00053902;
	data_array[1]= (y1_MSB<<24)|(y0_LSB<<16)|(y0_MSB<<8)|0x2b;
	data_array[2]= (y1_LSB);
	dsi_set_cmdq(data_array, 3, 1);

	data_array[0]= 0x00290508; //HW bug, so need send one HS packet
	dsi_set_cmdq(data_array, 1, 1);
	
	data_array[0]= 0x002c3909;
	dsi_set_cmdq(data_array, 1, 0);

}
#endif

LCM_DRIVER cpt_claa101fp01_dsi_vdo_lcm_drv = 
{
    .name			= "CPT_CLAA101FP01_DSI_VDO",
	.set_util_funcs = lcm_set_util_funcs,
	.get_params     = lcm_get_params,
	.init           = lcm_init,
	.suspend        = lcm_suspend,
	.resume         = lcm_resume,
	//.compare_id     = lcm_compare_id,
#if (LCM_DSI_CMD_MODE)
    .update         = lcm_update,
#endif
    };